Export limit exceeded: 26276 CVEs match your query. Please refine your search to export 10,000 CVEs or fewer.
Search
Search Results (26276 CVEs found)
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2026-99228 | 1 Linux | 2 Linux, Linux Kernel | 2026-11-06 | 3.3 Low |
| In the Linux kernel, the following vulnerability has been resolved: io_uring/io-wq: don't lose the signal that ends work When a thread exits, only its tracked requests are cancelled. Then its io-wq is torn down. io_wq_exit_workers() signals every worker, to get it out of an interruptible sleep, and waits for all of them to exit. Before they do, they go through the work that is left. Unbounded work is cancelled. Bounded work is run, as it is expected to end by itself. Not all of it does. An open has no file yet, so it counts as bounded, and the open of a FIFO waits for the other end. That is what the signal is for. But the workers are signalled once, and a worker that hasn't started the work by then loses the signal: io_wq_exit_workers() io_worker_handle_work() io_wq_worker_wake() set TIF_NOTIFY_SIGNAL io_assign_current_work() io_run_task_work() clear TIF_NOTIFY_SIGNAL io_wq_submit_work() fifo_open() wait_for_partner() wait_for_completion_timeout() The thread never gets out of do_exit(): IORING_OP_OPENAT of a FIFO without a writer, IOSQE_ASYNC exit of the thread that has submitted it hangs in more than 9 of 10 attempts (4 CPUs, KVM), until the process is killed. Set TIF_NOTIFY_SIGNAL for bounded work that is started with IO_WQ_BIT_EXIT set. The bit is set before the workers are signalled, and it is tested after the flag has been cleared, with clear_notify_signal() providing the barrier. So either the flag stays, or the bit is seen. Work that is started while the io-wq exits is treated like work that is being run at that time: it isn't interrupted unless it waits interruptibly. | ||||
| CVE-2026-99183 | 1 Linux | 2 Linux, Linux Kernel | 2026-11-06 | 4.4 Medium |
| In the Linux kernel, the following vulnerability has been resolved: accel/rocket: search every core slot when looking up a scheduler sched_to_core() walks rdev->cores[] up to rdev->num_cores, and rocket_remove() decrements num_cores for every core it removes. Unbind a core that is not the last one and the cores behind it fall outside the search, so sched_to_core() returns NULL for a core that is still bound and still running jobs. Neither caller checks the result: rocket_job_run(): rocket_fence_create(core), core->dev rocket_job_timedout(): dev_err(core->dev, "NPU job timed out") Unbinding the middle core of the three on an RK3588 while three clients are submitting to all of them faults twice, once from the surviving core's job queue and once from its reset work: KASAN: null-ptr-deref in range [0x0000000000000220-0x0000000000000227] Workqueue: fdad0000.npu drm_sched_run_job_work [gpu_sched] pc : rocket_job_run+0x234/0x838 [rocket] Call trace: rocket_job_run+0x234/0x838 [rocket] drm_sched_run_job_work+0x2cc/0xad8 [gpu_sched] process_one_work+0x640/0x14f0 KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007] Workqueue: rocket-reset-2 drm_sched_job_timedout [gpu_sched] pc : rocket_job_timedout+0xf0/0x1e0 [rocket] Call trace: rocket_job_timedout+0xf0/0x1e0 [rocket] drm_sched_job_timedout+0x188/0x6a0 [gpu_sched] Both are the third core: the workqueue names are its device and its core->index, and it was left at slot 2 while num_cores had dropped to 2. Search all the slots that were allocated, the way find_core_for_dev() now does. A core that is still bound is then found, and the two callers get the pointer they already assume they have. This does not make unbinding one core out of several safe. An open client keeps an entity pointing at the scheduler of the core that went away: drm_sched reports it as not ready for every job that lands on it, and the client waits in dma_fence_default_wait for a fence that will never signal. Stopping the NULL dereference is what belongs in a fix; the rest wants more thought. | ||||
| CVE-2026-98692 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 2.3 Low |
| In the Linux kernel, the following vulnerability has been resolved: thunderbolt: Make the DP tunnel activation callback mandatory tb_tunnel_alloc_dp() takes an optional callback which is run from dprx_work once the DPRX capabilities read has completed. Without that callback tb_dp_dprx_start() reads the capabilities synchronously and never queues the work. It however always takes a tunnel reference which is only dropped by dprx_work itself or by tb_dp_dprx_stop() when cancel_delayed_work() actually canceled that work. That reference is thus leaked for every tunnel without a callback. The only tunnels without one are those from tb_tunnel_discover_dp(), which are activated again when restoring from hibernation. Pass the callback to tb_tunnel_discover_dp() as well and drop the synchronous path such that the DPRX capabilities are always read from dprx_work. Hibernation restore then also no longer blocks for up to 12 seconds while waiting for that read to complete. Also fix up the KUnit tests. | ||||
| CVE-2026-97538 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: hwmon: (asus_rog_ryujin) Validate HID report lengths rog_ryujin_raw_event() parses response headers and payload fields without first checking that they are present in the received report. A short report can therefore make the driver consume uninitialized bytes from the HID transport buffer and expose them as sensor values through sysfs. Validate the response header and the fields used by each response type before parsing them. | ||||
| CVE-2026-89755 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: mm/migrate_device: clear stale mapping after freeing swapcache __migrate_device_pages() reads the folio mapping before calling folio_free_swap(). When folio_free_swap() succeeds, the folio is removed from the swap cache, but the saved mapping still points to swap_space. Passing the stale mapping to folio_migrate_mapping() makes it use the mapped-folio path for a folio that is no longer in swapcache. It can then operate on swap_space.i_pages with invalid reference accounting, eventually triggering a folio reference count BUG. After a successful split, nr still contains the number of pages in the original large folio, although each resulting page is now a separate order-0 folio. Reset nr to 1 so each split folio is processed separately, including its own swapcache removal and mapping lookup. Refresh the saved mapping after folio_free_swap() so the current folio state is used during migration. | ||||
| CVE-2026-80668 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 9.8 Critical |
| In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_conntrack_expect: use conntrack GC to reap expectations This patch replaces the timer API by GC worker approach for expectations, as it already happened in many other subsystems. Use the existing conntrack GC worker to iterate over the local list of expectations in the master conntrack to reap expired expectations. Check IPS_HELPER_BIT to run GC for expectations, set it on for nft_ct expectation which nevers sets it. Hold the expectation spinlock while iterating over the master conntrack expectation list to synchronize with nf_ct_remove_expectations(). This also performs runtime packet path garbage collection through the expectation insertion and lookup functions while walking over one of the chains of the global expectation hashtables. Unconfirmed conntrack entries are skipped since ct->ext can be reallocated and dying are skipped since those will be gone soon. Set on IPS_HELPER_BIT if the helper ct extension is added, then the new GC worker does not need to bump the ct refcount to check if the ct->ext helper is available. This removes the extra bump on the refcount for expectation timers, this allows to remove several nf_ct_expect_put() calls after the unlink, after this update only refcount remains at 1 while on the expectation hashes. This patch implicitly addresses a race with the existing timer API allowing an expectation to access a stale exp->master pointer which has been already released when expectation removal loses races with an expiring timer, ie. timer_del() reporting false. Add a new NF_CT_EXPECT_DEAD flag to reap this expectation via GC. This is needed by nf_conntrack_unexpect_related() which is called in error paths to invalidate newly created expectations that has been added into the hashes. These expectactions cannot be inmediately released as GC or nf_ct_remove_expectations() could race to make it. On expectation insert, the runtime GC reaps stale expectations before checking the expectation limit set by policy. Set current timestamp in nf_ct_expect_alloc(), then add the expectation policy timeout (or custom timeout specified added on top of this) to specify the expectation lifetime. | ||||
| CVE-2026-45963 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: ASoC: nau8821: Cancel delayed work on component remove Attempting to unload the driver while a jack detection work is pending would likely crash the kernel when it is eventually scheduled for execution: [ 1984.896308] BUG: unable to handle page fault for address: ffffffffc10c2a20 [...] [ 1984.896388] Hardware name: Valve Jupiter/Jupiter, BIOS F7A0131 01/30/2024 [ 1984.896396] Workqueue: events nau8821_jdet_work [snd_soc_nau8821] [ 1984.896414] RIP: 0010:__mutex_lock+0x9f/0x11d0 [...] [ 1984.896504] Call Trace: [ 1984.896511] <TASK> [ 1984.896524] ? snd_soc_dapm_disable_pin+0x26/0x60 [snd_soc_core] [ 1984.896572] ? snd_soc_dapm_disable_pin+0x26/0x60 [snd_soc_core] [ 1984.896596] snd_soc_dapm_disable_pin+0x26/0x60 [snd_soc_core] [ 1984.896622] nau8821_jdet_work+0xeb/0x1e0 [snd_soc_nau8821] [ 1984.896636] process_one_work+0x211/0x590 [ 1984.896649] ? srso_return_thunk+0x5/0x5f [ 1984.896670] worker_thread+0x1cd/0x3a0 Cancel unscheduled jdet_work or wait for its execution to finish before the component driver gets removed. | ||||
| CVE-2026-45961 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: gfs2: fix memory leaks in gfs2_fill_super error path Fix two memory leaks in the gfs2_fill_super() error handling path when transitioning a filesystem to read-write mode fails. First leak: kthread objects (thread_struct, task_struct, etc.) When gfs2_freeze_lock_shared() fails after init_threads() succeeds, the created kernel threads (logd and quotad) are never destroyed. This occurs because the fail_per_node label doesn't call gfs2_destroy_threads(). Second leak: quota bitmap buffer (8192 bytes) When gfs2_make_fs_rw() fails after gfs2_quota_init() succeeds but before other operations complete, the allocated quota bitmap is never freed. The fix moves thread cleanup to the fail_per_node label to handle all error paths uniformly. gfs2_destroy_threads() is safe to call unconditionally as it checks for NULL pointers. Quota cleanup is added in gfs2_make_fs_rw() to properly handle the withdrawal case where quota initialization succeeds but the filesystem is then withdrawn. Thread leak backtrace (gfs2_freeze_lock_shared failure): unreferenced object 0xffff88801d7bca80 (size 4480): copy_process+0x3a1/0x4670 kernel/fork.c:2422 kernel_clone+0xf3/0x6e0 kernel/fork.c:2779 kthread_create_on_node+0x100/0x150 kernel/kthread.c:478 init_threads+0xab/0x350 fs/gfs2/ops_fstype.c:611 gfs2_fill_super+0xe5c/0x1240 fs/gfs2/ops_fstype.c:1265 Quota leak backtrace (gfs2_make_fs_rw failure): unreferenced object 0xffff88812de7c000 (size 8192): gfs2_quota_init+0xe5/0x820 fs/gfs2/quota.c:1409 gfs2_make_fs_rw+0x7a/0xe0 fs/gfs2/super.c:149 gfs2_fill_super+0xfbb/0x1240 fs/gfs2/ops_fstype.c:1275 | ||||
| CVE-2026-45953 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: md/raid5: fix IO hang with degraded array with llbitmap When llbitmap bit state is still unwritten, any new write should force rcw, as bitmap_ops->blocks_synced() is checked in handle_stripe_dirtying(). However, later the same check is missing in need_this_block(), causing stripe to deadloop during handling because handle_stripe() will decide to go to handle_stripe_fill(), meanwhile need_this_block() always return 0 and nothing is handled. | ||||
| CVE-2026-45949 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 4.7 Medium |
| In the Linux kernel, the following vulnerability has been resolved: hwrng: core - use RCU and work_struct to fix race condition Currently, hwrng_fill is not cleared until the hwrng_fillfn() thread exits. Since hwrng_unregister() reads hwrng_fill outside the rng_mutex lock, a concurrent hwrng_unregister() may call kthread_stop() again on the same task. Additionally, if hwrng_unregister() is called immediately after hwrng_register(), the stopped thread may have never been executed. Thus, hwrng_fill remains dirty even after hwrng_unregister() returns. In this case, subsequent calls to hwrng_register() will fail to start new threads, and hwrng_unregister() will call kthread_stop() on the same freed task. In both cases, a use-after-free occurs: refcount_t: addition on 0; use-after-free. WARNING: ... at lib/refcount.c:25 refcount_warn_saturate+0xec/0x1c0 Call Trace: kthread_stop+0x181/0x360 hwrng_unregister+0x288/0x380 virtrng_remove+0xe3/0x200 This patch fixes the race by protecting the global hwrng_fill pointer inside the rng_mutex lock, so that hwrng_fillfn() thread is stopped only once, and calls to kthread_run() and kthread_stop() are serialized with the lock held. To avoid deadlock in hwrng_fillfn() while being stopped with the lock held, we convert current_rng to RCU, so that get_current_rng() can read current_rng without holding the lock. To remove the lock from put_rng(), we also delay the actual cleanup into a work_struct. Since get_current_rng() no longer returns ERR_PTR values, the IS_ERR() checks are removed from its callers. With hwrng_fill protected by the rng_mutex lock, hwrng_fillfn() can no longer clear hwrng_fill itself. Therefore, if hwrng_fillfn() returns directly after current_rng is dropped, kthread_stop() would be called on a freed task_struct later. To fix this, hwrng_fillfn() calls schedule() now to keep the task alive until being stopped. The kthread_stop() call is also moved from hwrng_unregister() to drop_current_rng(), ensuring kthread_stop() is called on all possible paths where current_rng becomes NULL, so that the thread would not wait forever. | ||||
| CVE-2026-45948 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: ext4: fix memory leak in ext4_ext_shift_extents() In ext4_ext_shift_extents(), if the extent is NULL in the while loop, the function returns immediately without releasing the path obtained via ext4_find_extent(), leading to a memory leak. Fix this by jumping to the out label to ensure the path is properly released. | ||||
| CVE-2026-45947 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: Fix memory leak in amdgpu_acpi_enumerate_xcc() In amdgpu_acpi_enumerate_xcc(), if amdgpu_acpi_dev_init() returns -ENOMEM, the function returns directly without releasing the allocated xcc_info, resulting in a memory leak. Fix this by ensuring that xcc_info is properly freed in the error paths. Compile tested only. Issue found using a prototype static analysis tool and code review. | ||||
| CVE-2026-45941 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: tpm: tpm_i2c_infineon: Fix locality leak on get_burstcount() failure get_burstcount() can return -EBUSY on timeout. When this happens, the function returns directly without releasing the locality that was acquired at the beginning of tpm_tis_i2c_send(). Use goto out_err to ensure proper cleanup when get_burstcount() fails. | ||||
| CVE-2026-45940 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: net: stmmac: fix oops when split header is enabled For GMAC4, when split header is enabled, in some rare cases, the hardware does not fill buf2 of the first descriptor with payload. Thus we cannot assume buf2 is always fully filled if it is not the last descriptor. Otherwise, the length of buf2 of the second descriptor will be calculated wrong and cause an oops: Unable to handle kernel paging request at virtual address ffff00019246bfc0 ... x2 : 0000000000000040 x1 : ffff00019246bfc0 x0 : ffff00009246c000 Call trace: dcache_inval_poc+0x28/0x58 (P) dma_direct_sync_single_for_cpu+0x38/0x6c __dma_sync_single_for_cpu+0x34/0x6c stmmac_napi_poll_rx+0x8f0/0xb60 __napi_poll.constprop.0+0x30/0x144 net_rx_action+0x160/0x274 handle_softirqs+0x1b8/0x1fc ... To fix this, the PL bit-field in RDES3 register is used for all descriptors, whether it is the last descriptor or not. | ||||
| CVE-2026-45925 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: thermal/of: Fix reference leak in thermal_of_cm_lookup() In thermal_of_cm_lookup(), tr_np is obtained via of_parse_phandle(), but never released. Use the __free(device_node) cleanup attribute to automatically release the node and fix the leak. [ rjw: Changelog edits ] | ||||
| CVE-2026-45923 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: net: usb: catc: enable basic endpoint checking catc_probe() fills three URBs with hardcoded endpoint pipes without verifying the endpoint descriptors: - usb_sndbulkpipe(usbdev, 1) and usb_rcvbulkpipe(usbdev, 1) for TX/RX - usb_rcvintpipe(usbdev, 2) for interrupt status A malformed USB device can present these endpoints with transfer types that differ from what the driver assumes. Add a catc_usb_ep enum for endpoint numbers, replacing magic constants throughout. Add usb_check_bulk_endpoints() and usb_check_int_endpoints() calls after usb_set_interface() to verify endpoint types before use, rejecting devices with mismatched descriptors at probe time. Similar to - commit 90b7f2961798 ("net: usb: rtl8150: enable basic endpoint checking") which fixed the issue in rtl8150. | ||||
| CVE-2026-45922 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: RDMA/mlx5: Fix memory leak in GET_DATA_DIRECT_SYSFS_PATH handler The UVERBS_HANDLER(MLX5_IB_METHOD_GET_DATA_DIRECT_SYSFS_PATH) function allocates memory for the device path using kobject_get_path(). If the length of the device path exceeds the output buffer length, the function returns -ENOSPC but does not free the allocated memory, resulting in a memory leak. Add a kfree() call to the error path to ensure the allocated memory is properly freed. Compile tested only. Issue found using a prototype static analysis tool and code review. | ||||
| CVE-2026-45920 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: ext4: fix dirtyclusters double decrement on fs shutdown fstests test generic/388 occasionally reproduces a warning in ext4_put_super() associated with the dirty clusters count: WARNING: CPU: 7 PID: 76064 at fs/ext4/super.c:1324 ext4_put_super+0x48c/0x590 [ext4] Tracing the failure shows that the warning fires due to an s_dirtyclusters_counter value of -1. IOW, this appears to be a spurious decrement as opposed to some sort of leak. Further tracing of the dirty cluster count deltas and an LLM scan of the resulting output identified the cause as a double decrement in the error path between ext4_mb_mark_diskspace_used() and the caller ext4_mb_new_blocks(). First, note that generic/388 is a shutdown vs. fsstress test and so produces a random set of operations and shutdown injections. In the problematic case, the shutdown triggers an error return from the ext4_handle_dirty_metadata() call(s) made from ext4_mb_mark_context(). The changed value is non-zero at this point, so ext4_mb_mark_diskspace_used() does not exit after the error bubbles up from ext4_mb_mark_context(). Instead, the former decrements both cluster counters and returns the error up to ext4_mb_new_blocks(). The latter falls into the !ar->len out path which decrements the dirty clusters counter a second time, creating the inconsistency. To avoid this problem and simplify ownership of the cluster reservation in this codepath, lift the counter reduction to a single place in the caller. This makes it more clear that ext4_mb_new_blocks() is responsible for acquiring cluster reservation (via ext4_claim_free_clusters()) in the !delalloc case as well as releasing it, regardless of whether it ends up consumed or returned due to failure. | ||||
| CVE-2026-45919 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: sched/rt: Skip currently executing CPU in rto_next_cpu() CPU0 becomes overloaded when hosting a CPU-bound RT task, a non-CPU-bound RT task, and a CFS task stuck in kernel space. When other CPUs switch from RT to non-RT tasks, RT load balancing (LB) is triggered; with HAVE_RT_PUSH_IPI enabled, they send IPIs to CPU0 to drive the execution of rto_push_irq_work_func. During push_rt_task on CPU0, if next_task->prio < rq->donor->prio, resched_curr() sets NEED_RESCHED and after the push operation completes, CPU0 calls rto_next_cpu(). Since only CPU0 is overloaded in this scenario, rto_next_cpu() should ideally return -1 (no further IPI needed). However, multiple CPUs invoking tell_cpu_to_push() during LB increments rd->rto_loop_next. Even when rd->rto_cpu is set to -1, the mismatch between rd->rto_loop and rd->rto_loop_next forces rto_next_cpu() to restart its search from -1. With CPU0 remaining overloaded (satisfying rt_nr_migratory && rt_nr_total > 1), it gets reselected, causing CPU0 to queue irq_work to itself and send self-IPIs repeatedly. As long as CPU0 stays overloaded and other CPUs run pull_rt_tasks(), it falls into an infinite self-IPI loop, which triggers a CPU hardlockup due to continuous self-interrupts. The trigging scenario is as follows: cpu0 cpu1 cpu2 pull_rt_task tell_cpu_to_push <------------irq_work_queue_on rto_push_irq_work_func push_rt_task resched_curr(rq) pull_rt_task rto_next_cpu tell_cpu_to_push <-------------------------- atomic_inc(rto_loop_next) rd->rto_loop != next rto_next_cpu irq_work_queue_on rto_push_irq_work_func Fix redundant self-IPI by filtering the initiating CPU in rto_next_cpu(). This solution has been verified to effectively eliminate spurious self-IPIs and prevent CPU hardlockup scenarios. | ||||
| CVE-2026-45917 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: ipvs: do not keep dest_dst if dev is going down There is race between the netdev notifier ip_vs_dst_event() and the code that caches dst with dev that is going down. As the FIB can be notified for the closed device after our handler finishes, it is possible valid route to be returned and cached resuling in a leaked dev reference until the dest is not removed. To prevent new dest_dst to be attached to dest just after the handler dropped the old one, add a netif_running() check to make sure the notifier handler is not currently running for device that is closing. | ||||