| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
HID: wacom: Advertise SW_MUTE_DEVICE capability prior to registration
Input subsystem guidelines require that device capabilities are advertised
before the input device is registered. The Wacom driver was violating
this by advertising the SW_MUTE_DEVICE capability post-registration in
wacom_set_shared_values() (and duplicating it in device-specific setup
cases).
Resolve this by moving the SW_MUTE_DEVICE capability setup to
wacom_setup_touch_input_capabilities() for all touch devices that support
it.
For generic touch devices whose capabilities depend on mute switch
usages parsed from a sibling Pen/Pad interface, defer registration
with -EPROBE_DEFER until the sibling has parsed its descriptors and
initialized shared capabilities. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: wacom: Fix Use-After-Free in wacom_intuos_pad
wacom_intuos_pad() accesses wacom->shared->touch_input locklessly
inside the interrupt handler context. If the Touch sibling device
is disconnected, wacom_remove_shared_data() clears 'touch_input'
outside any lock, creating a Time-of-Check to Time-of-Use (TOCTOU)
race condition where a preempted reader in interrupt context
dereferences the freed pointer, leading to a Use-After-Free.
Resolve this by introducing RCU protection for the touch_input
pointer:
- Annotate 'touch_input' in wacom_shared struct with __rcu
- Wrap all lockless readers in wacom_wac.c with guard(rcu)() and
rcu_dereference() using a unified wacom_report_touch_mute()
helper
- Update writers in wacom_sys.c using rcu_assign_pointer()
- Call synchronize_rcu() in wacom_remove_shared_data() to ensure
all active RCU readers have finished before the input device is
freed
Also wrap wacom_set_shared_values() and touch/pen assignments in
wacom_add_shared_data() inside the wacom_udev_list_lock to serialize
concurrent probe assignments, and verify that 'shared->touch == hdev'
before setting touch_input to prevent concurrent sibling probe state
desynchronization. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: wacom: Fix Use-After-Free in wacom_bamboo_pad
wacom_bamboo_pad_pen_event() accesses wacom->shared->pen locklessly
relative to wacom_remove_shared_data() which nullifies it. This
can lead to a Use-After-Free if the sibling device is removed while
events are being processed.
Resolve this by introducing RCU protection for pen and touch
pointers:
- Annotate 'pen' and 'touch' in wacom_shared struct with __rcu.
- Wrap lockless readers in wacom_bamboo_pad_pen_event() with
rcu_read_lock() and rcu_dereference().
- Update writers in wacom_sys.c using rcu_assign_pointer().
- Use rcu_dereference_protected for comparisons under
wacom_udev_list_lock.
- Also use rcu_access_pointer in wacom_sibling_pending() and
wacom_mode_change_work() to avoid warnings (while lockless access in
the latter remains a pre-existing issue). |
| In the Linux kernel, the following vulnerability has been resolved:
HID: wacom: Redesign shared sibling data lifecycle
The Wacom driver coordinates state between sibling interfaces of
the same physical device using a shared structure 'wacom_shared'
inside 'wacom_hdev_data'. The driver kept a volatile representative
pointer 'data->dev' pointing to a sibling 'hid_device' for physical
path comparisons during sibling matching.
This pointer management is fragile. When the representative device
is disconnected, wacom_remove_shared_data() failed to clear/update
'data->dev', leading to a Use-After-Free vulnerability when
subsequent sibling probes dereference the dangling 'data->dev'
pointer.
Resolve this issue by redesigning the sibling data lifecycle:
- Eliminate the volatile 'data->dev' representative pointer
completely
- Redesign 'wacom_hdev_data' to store stable static copies of the
required attributes upon first allocation: 'phys' path string,
'vendor', 'product' IDs and the sibling's 'device_type'
- Use these static attributes for stable sibling matching in
wacom_are_sibling() and wacom_get_hdev_data()
This ensures sibling matching remains safe and stable even if
individual siblings are dynamically added or removed.
To secure the lifecycle against concurrent probe/disconnect races:
- Switch kref_put() to kref_put_mutex() in
wacom_remove_shared_data() to serialize refcount drops with list
traversal and lookup
- Modify wacom_release_shared_data() to assume the list lock is
already held
Also, do not accumulate the 'device_type' capability flag during
subsequent sibling probes. Keeping only the first probed sibling's
device_type exactly preserves the original sibling matching behavior
without introducing side effects. |
| In the Linux kernel, the following vulnerability has been resolved:
klist: avoid accesses after waking klist_remove()
klist_remove() waits until a node is unreferenced so that its caller can
free the containing object. klist_release() currently publishes
waiter->woken and wakes the waiter before its final accesses to the waiter
and node. klist_remove() can then return, allowing its stack waiter and
the containing object to be freed or reused while klist_release() is still
running. In particular, bus_remove_driver() can free drv->p while
__device_attach() walks the same bus klist with bus_for_each_drv().
On an arm64 Cortex-A72 system, an unpatched 7.2.0-rc3 kernel with
CONFIG_PREEMPT_RT=y and CONFIG_KASAN=y reproduced the bug through the
in-tree I2C/at24 path. KASAN reported a use-after-free in
klist_dec_and_del() reached from klist_next()/bus_for_each_drv() while
at24 was being unregistered.
Clear n_klist and take a task reference before publishing woken. Use
release/acquire accesses for that publication and wake the referenced
task. The task reference keeps the waiter task alive if it returns and
exits before wake_up_process(). |
| In the Linux kernel, the following vulnerability has been resolved:
rust: bug: pass TAINT_WARN to warn_slowpath_fmt() on UML
On UML, `warn_flags!` calls `warn_slowpath_fmt()` directly. Its third
argument is a taint number, but `warn_on!` passes its bug flags there.
As a result, `add_taint()` gets 2304 instead of 9 (`TAINT_WARN`). The
warning is not recorded: `/proc/sys/kernel/tainted` stays 0 after
`warn_on!` fires, where it should be 512. It also causes an
out-of-bounds write in `add_taint()`.
Pass `TAINT_WARN` directly, as C does on UML. |
| In the Linux kernel, the following vulnerability has been resolved:
rust: configfs: fix data offset calculation for subsystem callbacks
`get_group_data()` chooses between `Group::<Parent>::container_of()` and
`Subsystem::<Parent>::container_of()` based on whether `this` represents
the root group of a configfs subsystem. It detects this by checking
`(*this).cg_subsys.is_null()`, but `link_group()` in `fs/configfs/dir.c`
unconditionally sets `cg_subsys` for every `config_group` attached anywhere
in a registered subsystem, including the subsystem's own `su_group`. The
only `config_group` with a NULL `cg_subsys` is the configfs root, on which
userspace cannot trigger callbacks. The check is therefore always false at
runtime, and the `Subsystem` branch is dead. Subsystem-level callbacks
reach the `Group` branch and may read `data` at the wrong offset.
Thus change the `is_root` check to correctly identify whether a group is a
root group by comparing `this` to `subsys.su_group`.
[ Andreas: Fix clippy warning on 1.85.0 by moving safety comment. ] |
| In the Linux kernel, the following vulnerability has been resolved:
accel/amdxdna: clear the mailbox channel pointer when starting it fails
aie2_create_context() allocates a mailbox channel, starts it, and on a
failed start frees it again:
hwctx->priv->mbox_chann = xdna_mailbox_alloc_channel(ndev->mbox);
...
ret = xdna_mailbox_start_channel(hwctx->priv->mbox_chann, ...);
if (ret)
goto free_channel;
...
free_channel:
xdna_mailbox_free_channel(hwctx->priv->mbox_chann);
hwctx->priv->mbox_chann keeps pointing at the freed channel. That
pointer is the driver's own test for whether a hardware context has a
usable channel: aie2_destroy_context() returns early on NULL,
aie2_sched_job_run() refuses to run a job on NULL, and the message
helpers return -ENODEV on NULL. A stale pointer passes all of them.
It matters on the restart path. aie2_hwctx_restart() calls
aie2_create_context() again on a hardware context that is already live,
after aie2_hwctx_stop() has torn its channel down, and the context
survives a failure there: aie2_sched_job_timedout() discards the return
value entirely, and aie2_hwctx_resume() only propagates it. What is
left is a live hardware context holding a freed channel, and every
later user of it takes the non-NULL branch:
- the next job submitted reaches xdna_mailbox_send_msg() on the freed
channel, via the !mbox_chann guard in aie2_sched_job_run(),
- a second command timeout reaches aie2_hwctx_stop() ->
aie2_destroy_context(),
- closing the device reaches aie2_hwctx_fini() ->
aie2_release_resource() -> xrs_release_resource() ->
aie2_xrs_unload() -> aie2_destroy_context(),
and aie2_destroy_context() then calls xdna_mailbox_stop_channel()
followed by xdna_mailbox_free_channel() on memory that was already
freed: a use-after-free, and a second free of the same channel.
The AIE4 management channel already does this correctly -
aie4_mailbox_start() clears ndev->aie.mgmt_chann right after freeing
it. Do the same here.
The create path itself is not affected: when aie2_xrs_load() fails,
xrs_allocate_resource() removes the solver node without calling
->unload, and aie2_hwctx_init() frees hwctx->priv, so the stale pointer
never outlives the structure holding it.
Starting a channel can fail today without this patch: the ring buffer
sizes firmware reports are rejected unless both are powers of two, and
request_irq() can fail. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: emux: Fix UAF of soundfont zones at note-on
snd_emux_note_on() looks up the matching zones via
snd_soundfont_search_zone(), which takes sflist->lock only during the
lookup and returns the raw zone pointers after releasing it. The
caller then stores them in vp->zone without any protection.
Meanwhile, a concurrent SNDRV_EMUX_IOCTL_REMOVE_LAST_SAMPLES ioctl may
unlink and free those zones in snd_soundfont_remove_unlocked(); this
leads to a use-after-free in snd_emux_note_on(), and later at
accessing the cached vp->zone, e.g. in snd_emux_send_effect().
Fix it by holding sflist->lock in snd_emux_note_on() over the whole
zone lookup and voice setup, and let snd_soundfont_search_zone()
require the caller to hold the lock, instead.
snd_soundfont_lock_preset() takes sflist->lock for setting
presets_locked, so the removal path now syncs with the note-on finish. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: pcmtest: handle multiple wraps in random capture fill
The random capture helpers assume that the data generated for one timer
tick wraps the DMA ring at most once. However, b_rw describes 200 ms of
audio because the timer runs at 5 Hz, so it can be several times larger
than a small ring.
For 48 kHz, S16_LE, four-channel capture with a 512-frame buffer, the DMA
ring is 4096 bytes while one tick generates 76800 bytes. After filling the
4096-byte tail, the existing code issues a second 72704-byte write from the
ring base, writing 68608 bytes beyond the ring. Both interleaved and
non-interleaved capture are affected.
KASAN reports the first write into the adjacent free page as a
use-after-free in the random-byte generator. The underlying defect is an
out-of-bounds write from the live DMA ring, not a stale DMA allocation.
Split each random write repeatedly at the interleaved ring or per-channel
block boundary. Keep the hardware-pointer update exactly once after the
complete logical write.
The issue reproduced on three of three clean boots. With this change, the
same vulnerable geometry completed six times without a sanitizer finding.
Boundary, pattern-fill, no-timer, open/close, and module-reload controls
also completed normally.
snd-pcmtest is a test driver, and selecting random fill requires an
administrator-controlled module parameter. The written values come from the
kernel random generator; no privilege escalation or attacker-controlled
write primitive was demonstrated. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: amd: ps: fix snd_acp63_remove() teardown ordering
The ACP IRQ handlers dereference the SoundWire, SoundWire DMA, and PDM
child platform devices, but snd_acp63_remove() unregisters them while
the interrupt is still held by devres, which frees it only after remove
returns. An interrupt in this window is a use-after-free.
Mask the ACP interrupt sources and call devm_free_irq() before the
first child device is unregistered. The masking goes through the new
acp_hw_ops->disable_interrupts callback, keeping the remove path
platform-agnostic. The interrupt line is shared, and acp_hw_deinit()
clears the sources only after the children are gone, which would
leave the line raised with no handler left to ack it. The window
predates the tagged refactor, which only reshaped the dereferences.
devm_free_irq() waits for in-flight handlers, but not for work the
hardirq has already queued: acp63_irq_handler() schedules
amd_sdw_irq_thread on the SoundWire manager. Draining that work in
the manager's remove path is a soundwire-side change and follows
separately.
This issue was found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_vhci: Pin module for debugfs file operations
An open debugfs file retains its file_operations pointer in the
debugfs proxy state. However, force_suspend_fops, force_wakeup_fops,
aosp_capable_fops, and force_devcoredump_fops have no .owner set to
THIS_MODULE. As a result, full_proxy_open_regular() calls fops_get()
which succeeds without taking a reference to the hci_vhci module.
When userspace opens any of these debugfs files and later closes
the /dev/vhci file descriptor (triggering vhci_release() and
debugfs file removal), the open debugfs file descriptor remains valid
in userspace. Because the module refcount was not incremented,
the hci_vhci module can be unloaded via delete_module (rmmod hci_vhci).
When the userspace process subsequently closes the debugfs file
descriptor, full_proxy_release() accesses the already unmapped
file_operations structure, resulting in a kernel page fault / oops:
BUG: unable to handle page fault for address: fffffbfff846f18b
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
Oops: Oops: 0000 [#1] SMP KASAN NOPTI
RIP: 0010:full_proxy_release+0x8e/0x140
Call Trace:
<TASK>
__fput+0x39f/0xa60
fput_close_sync+0xff/0x200
__x64_sys_close+0x8c/0xf0
do_syscall_64+0xc3/0x590
entry_SYSCALL_64_after_hwframe+0x76/0x7e
</TASK>
Modules linked in: ... [last unloaded: hci_vhci(E)]
The issue was discovered via manual code audit of
drivers/bluetooth/hci_vhci.c and verified on a Linux 7.3-rc6 test VM
with CONFIG_BT_VHCI=m by keeping a debugfs file open across controller
teardown and module unload.
Set .owner = THIS_MODULE on all four file_operations structures so that
debugfs pins the module until all file descriptors are closed. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/panthor: Fix TOCTOU race between GROUP_REGISTERED check and erase
panthor_group_destroy() checks the GROUP_REGISTERED mark and then calls
xa_erase() without holding the xarray lock across both. If the handle is
destroyed by another thread in between, and a concurrent GROUP_CREATE
reuses the freed ID, the first destroy erases and releases the new,
still-initializing group, leading to a use-after-free in
panthor_group_create().
Do the mark check and erase atomically under xa_lock(). |
| In the Linux kernel, the following vulnerability has been resolved:
fbdev: atmel_lcdfb: Prevent FIFO work after removal
The LCD controller IRQ schedules sinfo->task to recover from a FIFO
underflow. Probe currently requests the IRQ before initializing the
work, so an early interrupt can schedule an uninitialized work item.
The probe error path and remove path cancel the work before freeing the
IRQ. A FIFO-underflow interrupt can schedule the work again after that
cancellation. framebuffer_release() may then free sinfo while the work
is still pending.
KASAN reported a use-after-free in atmel_lcdfb_task() when an underflow
interrupt occurred during removal. With the IRQ freed before the work
was cancelled, the same test completed without a kernel diagnostic.
Initialize the work before requesting the IRQ. In both cleanup paths,
free the IRQ before cancelling the work so that it cannot be scheduled
again after cancellation. |
| In the Linux kernel, the following vulnerability has been resolved:
filelock: keep superblock active through delegation wait
A caller may drop its path after try_break_deleg() returns a delegated
inode but before break_deleg_wait() finishes. The extra inode reference
held in struct delegated_inode does not keep the superblock active.
After a lazy unmount, closing the delegation holder can release the last
mount reference and shut down the superblock while another task waits for
the delegation break. The waiter's final iput() can then enter the
filesystem's eviction code after its superblock-private state was freed.
This has been observed as a KASAN use-after-free in shmem_evict_inode().
When try_break_deleg() saves a delegated inode, take an active reference
to its superblock while the caller still pins the mount. Keep that
reference through break_deleg_wait() and the final iput(), then release
it with deactivate_super(). This protects every caller of the helpers,
including the mknod, mkdir, symlink and rmdir paths that drop their path
before waiting. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/proc/task_mmu: pin mm_users in do_pagemap_scan()
The PAGEMAP_SCAN ioctl takes mmap_read_lock() on an mm obtained from
/proc/<pid>/pagemap without holding a reference to mm_users.
proc_mem_open() deliberately grabs only mm_count, so a consumer that
touches the address space has to call mmget_not_zero() first. Every other
consumer in this file does -- m_start(), do_procmap_query(),
show_smaps_rollup() and pagemap_read() -- but do_pagemap_scan() does not.
Without that reference the target can reach exit_mmap() concurrently, and
exit_mmap() calls unmap_vmas() while holding mmap_lock only for reading,
which does not exclude the scanner. For ordinary VMAs this is harmless,
as free_pgtables() and remove_vma() run afterwards under mmap_write_lock.
A shared hugetlb VMA is different: __hugetlb_zap_end() frees the VMA's
hugetlb_vma_lock inside the read-locked phase.
walk_hugetlb_range() can therefore load vma->vm_private_data, have the
lock freed underneath it, and then down_read() a freed rw_semaphore. The
load happens before the freeing side clears the pointer, so this is a
use-after-free and not a NULL dereference. Any unprivileged user can
reach it with no huge pages configured, as hugetlb_reserve_pages()
allocates the lock before the VM_NORESERVE early return.
Pin mm_users across the scan, the way the other consumers do. mmput()
from the exiting task can then no longer reach exit_mmap() while a walk is
in progress.
[akpm@linux-foundation.org: remove unneeded & undesirable test for !mm] |
| In the Linux kernel, the following vulnerability has been resolved:
fsverity: Set S_VERITY only after rollback is no longer possible
Commit f77f281b6118 ("fsverity: use a hashtable to find the
fsverity_info") changed the implementation of FS_IOC_ENABLE_VERITY to
make concurrent reads start going through fsverity verification slightly
earlier than they did before.
Instead of it happening when enable_verity() calls fsverity_set_info(),
it now happens when ->end_enable_verity() sets S_VERITY.
However, ext4 and btrfs can roll back verity after they set S_VERITY,
causing a use-after-free.
Fix that by making ext4 and btrfs set S_VERITY only after rollback is no
longer possible. On failure, don't roll back S_VERITY, but do roll back
the filesystem-specific verity flag.
Also update enable_verity() to handle any future instances of this bug
more safely by warning and *not* freeing the fsverity_info.
Finally, tweak some comments. Clarify one, and move information from
another to its proper place in the comment for ->end_enable_verity(). |
| In the Linux kernel, the following vulnerability has been resolved:
genirq: Defer kfree(irqaction) until irq_thread_dtor() finishes
When an interrupt thread exits abnormally via do_exit() (e.g. the interrupt
handler oopses) without returning from irq_thread(), a concurrent call to
free_irq() could free the irqaction before the irq_thread_dtor() exit task
work runs.
irq thread (oopsed) free_irq()
------------------- ----------
do_exit()
exit_mm()
complete_vfork_done() -------> kthread_stop() returns
exit_files() ... kfree(action)
exit_task_work()
irq_thread_dtor()
action->... <- use-after-free
Track the pending exit work with the IRQTF_EXIT_WORK thread flag, and have
__free_irq() wait for the bit to clear before kfree().
irq_thread_dtor() only runs on irq_thread abnormal exit. If that dtor also
faults, free_irq() will hang indefinitely, but double IRQ thread faults
require a reboot anyways.
[ tglx: Add missing include ] |
| In the Linux kernel, the following vulnerability has been resolved:
HID: hiddev: keep state alive through disconnect unlock
mutex_unlock() clears the mutex owner before taking its wait lock. A
thread spinning in the final hiddev file release can acquire
existancelock after hiddev_disconnect() clears the owner, then free
hiddev before the disconnecting thread reaches the mutex wait lock. This
causes a use-after-free in the mutex slow unlock path.
Give the connection and each open file an explicit reference. Drop each
reference only after its existancelock critical section has completed,
so neither unlock path can free the mutex while the other is still using
it. |
| Use-after-free in magic method backtraces can lead to remote code execution.
When collecting the arguments of a method call handled by __call() or __callStatic() for a backtrace, PHP can read stale values that may refer to freed memory. If a fatal error such as exceeding memory_limit occurs while an application enters such a call, with fatal_error_backtraces enabled (the default) and zend.exception_ignore_args disabled, a remote attacker who controls enough request data to influence memory allocation may cause memory corruption, crash the PHP worker or, with knowledge of memory addresses, execute arbitrary code. php.ini-production enables zend.exception_ignore_args, which prevents this.
This issue affects PHP versions 8.5.* before 8.5.13. |