| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
xfs: refuse a pNFS LAYOUTCOMMIT of a range without blocks
A client can commit a hole in a LAYOUTCOMMIT, because nfsd does not
check the extents against its layouts. xfs_iomap_write_unwritten() then
allocates written blocks there. A large hole overruns the block
reservation and shuts XFS down. A small one exposes stale data.
Refuse such a range with -EIO, using XFS_BMAPI_CONVERT_ONLY. |
| In the Linux kernel, the following vulnerability has been resolved:
can: dev: can_dropped_invalid_skb: drop CAN XL frames on non-CAN XL devices
Sending a PF_PACKET bypasses the CAN framework logic and can directly
reach a CAN driver's xmit() function. The PF_PACKET framework only
checks that skb->len does not exceed the net_device MTU.
For a CAN device that is not CAN XL capable, anything above CANFD_MTU
(72 bytes) is therefore dropped before it reaches the driver. However,
CAN XL frames are variable length. can_is_canxl_skb() accepts lengths in
the range CANXL_HDR_SIZE + CANXL_MIN_DLEN up to CANXL_MTU, i.e. 13 to
2060 bytes.
As a result, an ETH_P_CANXL skb with a length between 13 and 72 bytes
can pass both the MTU and the can_dropped_invalid_skb() checks.
A driver that does not support CAN XL will interpret canxl_frame->flags
as a length because of the overlap with can_frame->len. And because
CANXL_XLF is set, the resulting length is between 128 and 255. For
drivers that do not check can_frame->len before copying can_frame->data,
as most drivers do, this results in a buffer overflow of up to 247
bytes.
Drop ETH_P_CANXL skbs if the device does not have the CAN_CAP_XL
capability. Keep can_is_canxl_skb() for the validation of CAN XL skbs. |
| In the Linux kernel, the following vulnerability has been resolved:
can: replace ARPHRD_CAN type checks with can_get_ml_priv()
Commit 4e096a18867a ("net: introduce CAN specific pointer in the struct
net_device") introduced an explicit way to assign the midlayer private
pointer (dev->ml_priv) to named users like ML_PRIV_CAN. A valid pointer
returned by can_get_ml_priv() therefore identifies a real CAN device.
The referenced commit only converted the j1939 and proc code to this
check, while the other parts of the CAN subsystem still rely on
dev->type == ARPHRD_CAN.
The TUNSETLINK ioctl allows a down TUN/TAP device to set its hardware
type to ARPHRD_CAN while dev->ml_priv remains NULL. Such a repurposed
netdevice passes the ARPHRD_CAN checks.
Commit 8aa59e355949 ("can: af_can: fix NULL pointer dereference in
can_rx_register()") already made can_rx_register() reject such devices.
But can_rx_unregister() still only checks dev->type and dereferences
the NULL ml_priv when it walks the receive lists of the device.
CAN_ISOTP reaches this path: isotp_bind() ignores the return values of
can_rx_register() and binds the socket anyway. When the socket is
released or the device is unregistered, isotp_release() and
isotp_notify() remove the filters that have never been registered and
trigger the NULL pointer dereference in can_rx_unregister(). This only
requires owning a TUN/TAP device or CAP_NET_ADMIN in an unprivileged
user namespace.
Convert the remaining ARPHRD_CAN checks in af_can, bcm, gw, isotp and
raw to can_get_ml_priv(). |
| In the Linux kernel, the following vulnerability has been resolved:
can: protect the receive lists with a per-device lock
The receive lists of a CAN device are located in the device's
can_ml_priv and travel with the device when it is moved to another
network namespace. But they are protected by the per-netns
rcvlists_lock. So can_rx_unregister() needs dev_net(dev) to pick the
right lock and silently returns when the passed namespace does not
match dev_net(dev) anymore.
isotp_release() and bcm_release() leave their notifier list before they
take any lock that serializes against the netdev notifier, which runs
under RTNL. When the bound device is moved to another namespace in this
window, the notifier skips the socket and the release path has to remove
the filters itself. isotp_release() passes the socket's namespace, which
does not match dev_net(dev) anymore. bcm_rx_unreg() passes dev_net(dev),
which can_rx_unregister() reads again for its check, so a namespace
change between both reads makes the check fail as well. In both cases
can_rx_unregister() silently returns. As can_rx_register() stores
rcv->sk without a reference, the remaining receivers point to the freed
socket (isotp) or the freed op (bcm):
BUG: KASAN: use-after-free in isotp_rcv+0x1570/0x24d0
Read of size 1 at addr ffff888118130552 by task isotp_ns_uaf/578
can_rcv_filter+0x4af/0x8c0
can_receive+0x28d/0x3c0
can_rcv+0x2a9/0x310
__netif_receive_skb_one_core+0x21a/0x260
process_backlog+0x210/0x760
Besides this, the lists of a device are protected by the rcvlists_lock
of the namespace that is passed in. Callers which pass dev_net(dev) read
it at different times, so the same lists may be modified under the locks
of different namespaces while the device is moved.
Taking RTNL in these release paths is no option: raw_bind(),
raw_setsockopt() and raw_release() already hold RTNL while adding and
removing up to CAN_RAW_FILTER_MAX filters per socket, which unprivileged
users can trigger repeatedly and which makes RTNL a global bottleneck.
Instead fix the root cause and add a spinlock to struct
can_dev_rcv_lists, which protects the receive lists of a CAN device or
the 'any' CAN device lists of a namespace. It is initialized in
can_set_ml_priv(), which is used by all CAN network devices. With this,
can_rx_unregister() finds the subscription independently of the
current namespace of the device. The protocols keep the device valid
with their tracked references. The per-netns rcvlists_lock only protects
the receive list statistics anymore, and CAN_RAW, CAN_BCM and CAN_ISOTP
pass the namespace that has been used for can_rx_register().
So isotp_release() and bcm_release() now remove their filters correctly
without RTNL, and raw_release(), raw_setsockopt(), raw_bind() and
isotp_bind() do not need RTNL anymore and add and remove their filters
under lock_sock(). To serialize bind() with NETDEV_UNREGISTER, bind()
publishes the device inside the RCU section of its lookup, and
raw_notify() and isotp_notify() recheck the bound device under lock_sock().
As RTNL does not keep NETDEV_DOWN out of bind() anymore, bind() checks
IFF_UP after publishing the bound device, with a barrier pair against
raw_notify() and isotp_notify(), so a down transition during bind() is
still reported with ENETDOWN. |
| In the Linux kernel, the following vulnerability has been resolved:
can: dev: can_fill_info(): don't wake up controller if interface is down
If the interface is down, the CAN controller might be powered down and
its clocks gated. Don't call do_get_berr_counter() to read the bus error
counters if the interface is down, and adjust can_get_size() to match.
This removes one trigger for a synchronous external abort seen on
i.MX8QXP when "ip link show" is run on a flexcan interface that was
never brought up. The underlying cause is platform-specific: on i.MX8QXP
the CAN clocks are gated through the SCU LPCG and the subsystem shares
the IMX_SC_R_CAN_0 power domain, and there is a window after
pm_runtime_resume_and_get() returns where the clock has not reached the
module yet. This patch avoids the netlink query path while the interface
is down, but does not root-cause the LPCG window itself.
As a result, IFLA_CAN_BERR_COUNTER is no longer reported for down
interfaces. Userspace must treat the attribute as optional.
The issue was triggered on an i.MX8QXP board by running "ip link show"
without ever bringing the interface up:
Internal error: synchronous external abort: 0000000096000210
pc : flexcan_read_le+0x0/0x18
lr : flexcan_get_berr_counter+0x4c/0x8c
Call trace:
flexcan_read_le+0x0/0x18
flexcan_get_berr_counter+0x4c/0x8c
can_fill_info+0x1f8/0x434
rtnl_fill_ifinfo+0x8fc/0xbb4
rtnl_dump_ifinfo+0x364/0x448
This is the same class of problem fixed for m_can in
commit 91a55c72a821 ("can: m_can: m_can_get_berr_counter(): don't
wake up controller if interface is down"). |
| In the Linux kernel, the following vulnerability has been resolved:
mm/huge_memory: fix truncate racing with PMD zapping
zap_huge_pmd_folio() removes the rmap before calling folio_mark_dirty().
If this was the last mapping, truncation can skip unmapping the folio
and proceed without waiting for the PMD lock, racing with dirtying.
ifs_set_range_dirty() can oops if MADV_DONTNEED races with
ftruncate() on XFS, when we get the folio set dirty after it was found
to not be mapped anymore.
Move folio_mark_dirty() and folio_mark_accessed() before rmap removal,
matching the PTE zap path. This keeps the folio mapped while updating
its state, so truncation must wait for the page table lock.
Fix generated by an LLM and sent by Chris Mason in private.
[ david: simplify comment and description ] |
| In the Linux kernel, the following vulnerability has been resolved:
mm/huge_memory: fix zapping migration entries for device-private THPs
A PMD migration entry can refer to a device-private folio.
zap_huge_pmd_folio() checks the folio type instead of the entry type,
so it treats such a migration entry as a device-private entry.
Installing the migration entry already removed the reverse mapping and
dropped the mapping reference. Zapping it must not repeat those
operations. Concurrent MADV_DONTNEED during migration back to system
memory can trigger this.
Check the PMD entry type using pmd_is_device_private_entry().
Fix generated by an LLM and sent by Chris Mason in private.
[ david: simplify description ] |
| In the Linux kernel, the following vulnerability has been resolved:
mm/khugepaged: always recheck the pmd in try_collapse_pte_mapped_thp()
try_collapse_pte_mapped_thp() drops the PTE lock after it has cleared the
page table, and takes the PMD lock and the PTE lock to remove it.
In between, MADV_DONTNEED with CONFIG_PT_RECLAIM can reclaim the
page table. The pmd_same() check is supposed to handle this, but it is
only done with CONFIG_SPLIT_PTE_PTLOCKS.
Fix it by performing the check unconditionally.
Fix generated by an LLM and sent by Josef Bacik in private.
[ david: adjust description ] |
| In the Linux kernel, the following vulnerability has been resolved:
mm/khugepaged: preserve dirty bits when collapsing PTE-mapped THPs
try_collapse_pte_mapped_thp() clears PTEs without transferring their dirty
bits to the folio. A shmem read fault can map a clean folio writable, so
a later store only dirties the PTE. Losing that dirty bit allows reclaim
to discard modified data.
The assumption that regular files are read-only is also obsolete since
commit 1b6444331bebb ("mm/khugepaged: enable clean pagecache folio collapse
for writable files"). In any case, transferring PTE dirty bits to the folio
when removing mappings (and while the folio is still mapped) is the right
thing to do.
Use get_and_clear_ptes() to collect the dirty bits and mark the folio
dirty before unmapping it. Update the comment.
This was reproduced with shmem using MADV_COLLAPSE followed by
MADV_PAGEOUT.
Fix generated by an LLM and sent by Chris Mason in private.
[ david: adjust comment; simplify description; cover file-thp as well ] |
| In the Linux kernel, the following vulnerability has been resolved:
mm/gup: recheck the PUD under PTL in follow_pud_mask()
follow_pud_mask() reads the PUD without a lock. If it is a leaf, it takes
the lock and calls follow_huge_pud(), which reads the entry again, but
only tests whether it is present.
A leaf can be zapped concurrently and a page fault can fill the empty
entry with a page table.
This currently only applies when device-dax makes use of PUD entries,
and the fault after e.g., MADV_DONTNEED would find THPs to be disabled.
That requires a sequence like
1) Fault in the PUD
2) Disable THP
3) Have GUP race against concurrent MADV_DONTNEED + refault
Which is rather unlikely to happen in practice, which is why we never
received a report about such a problem.
Before commit 1b1676180246 ("mm/gup: handle huge pud for
follow_pud_mask()"), we performed that check in follow_devmap_pud() by
testing for pud_devmap().
Let's fix it by just structuring follow_pud_mask() similar to
follow_pmd_mask(), minus protnone stuff that does not apply and minus
FOLL_SPLIT_PMD handling. That makes it much easier to spot any such
inconsistencies.
Perform the pud_bad() check early in follow_pmd_mask() and just forward
the PUD value. We can drop the pud_present() check in follow_huge_pud(),
just like we have in follow_huge_pmd().
Even though we are performing more changes than strictly necessary, the
fix should be easy to backport. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/gup: fix clearing folios in memfd_pin_folios()
memfd_pin_folios() pins folios obtained directly from the page cache
without checking whether they are uptodate. However, shmem fallocate()
can leave newly allocated folios uncleared and not uptodate. Callers
such as udmabuf can then expose uninitialized memory to userspace.
Clear non-uptodate folios and mark them uptodate under the folio lock
before returning them to the caller.
Fix generated by an LLM and sent by Chris Mason in private.
[ david: simplify description and comment ] |
| In the Linux kernel, the following vulnerability has been resolved:
mm/gup: fix out-of-bounds write for nr_pages == 0 in GUP-fast
With nr_pages == 0, GUP-fast still enters its page table walk and can
write past the caller's page array. The old end <= start check caught
empty ranges, but was replaced with an overflow check.
Users such as OrangeFS can pass a zero page count derived from a
userspace-supplied length. So let's return zero for nr_pages == 0 before
starting the walk, just like GUP-slow.
Fix generated by an LLM and sent by Chris Mason in private.
[ david: simplify description ] |
| In the Linux kernel, the following vulnerability has been resolved:
mm/gup: check for overflow when converting nr_pages to bytes in GUP-fast
The overflow check in gup_fast_fallback() only covers the addition to
start. The preceding nr_pages << PAGE_SHIFT can already have truncated
the length on 32bit.
Users such as RapidIO's rio_dma_transfer() can derive such page counts
from a 64-bit userspace length.
Let's just check_shl_overflow() to reject any such overflow with
-EOVERFLOW early. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/userfaultfd: write-lock the VMA before waking waiters when unregistering
userfaultfd_unregister() wakes pending missing faults before clearing the
VMA's userfaultfd registration. With per-VMA fault locking, holding
mmap_lock for write does not prevent another fault from queuing after
the wakeup but before userfaultfd_clear_vma() write-locks the VMA. That
waiter can then remain asleep indefinitely.
Call vma_start_write() before waking waiters. Existing fault handlers
queue themselves before dropping the VMA read lock, and new readers are
excluded until mmap_write_unlock(). |
| In the Linux kernel, the following vulnerability has been resolved:
mm/ksm: reset the unstable trees of all nodes
Each full scan resets ksm_nr_node_ids unstable tree roots. Enabling
merge_across_nodes resets this count to 1, even if per-node roots were
previously allocated.
So when toggling "merge_across_nodes" 0 -> 1 -> 0, a scan that starts
while the setting is 1 and continues after switching back to 0 can
encounter stale unstable tree roots, resulting in UAF.
Only root is allowed to change "merge_across_nodes", and the documented
sequence is: "merge_across_nodes setting can be changed only when there
are no ksm shared pages in the system: set run 2 to unmerge pages first,
then to 1 after changing merge_across_nodes, to remerge according to the
new setting."
Let's fix it by tracking in ksm_nr_node_ids the actual number of
allocated tree roots.
remove_all_stable_nodes() and ksm_check_stable_tree() will now scan
more tree roots (skipping the empty ones), which is harmless. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/cma: don't release CMA pages still in use
When a driver calls dma_free_contiguous() before quiescing DMA, the
page might still have a reference from the device.
put_page_testzero() there returns false, WARN fires, but the code proceeds
to free_contig_frozen_range() putting a live page onto buddy and clearing
the bitmap. A subsequent allocation can hand the same PFN to a new
owner while the original holder still references it.
A concurrent put_page() that drops the last reference between the
testzero loop and free_contig_frozen_range() can double-queue the page
via page->lru, corrupting buddy lists.
Avoid the corruption by not freeing a CMA region if any of the
pages inside are still in use.
Make it explicit in the warning that the driver allowed a leak.
While at it, use page_ref_freeze() to make the semantics clearer and
switch to pr_warn_ratelimited().
[ david: use page_ref_freeze() + pr_warn_ratelimited() ] |
| In the Linux kernel, the following vulnerability has been resolved:
mm/memory-tiers: unregister empty tiers outside memory_tier_lock
When offlining a node's last memory empties its tier,
clear_node_memory_tier() calls device_unregister() while holding
memory_tier_lock. A concurrent sysfs read can hold a kernfs active
reference and block in nodelist_show() on that mutex. device_unregister()
then waits in kernfs_drain() for the read to finish and release its active
reference, while the reader waits for the offlining task to release the
mutex.
Return the node's former tier from clear_node_memory_tier(), making the
helper more similar to set_node_memory_tier(), which also returns a
memory_tier pointer. Let the caller unlink an empty tier under
memory_tier_lock before rebuilding demotion targets, then unregister its
device after dropping the lock. |
| In the Linux kernel, the following vulnerability has been resolved:
ovl: do not let chattr change the casefold flag
chattr +F or -F on an overlay directory can make the directory, or the
whole mount, unusable. Lookups of the directory, and lookups in it, then
fail. From code inspection, the caller only needs to own the directory.
The upper filesystem must support casefolding: ext4 or f2fs with the
casefold feature, or tmpfs with the casefold option.
chattr +F and -F set and clear FS_CASEFOLD_FL, the casefold flag of a
directory. The flag enables casefolding (case-insensitive name lookup)
for the directory. All directories of an overlay must match the casefold
state that was recorded at mount time, and ovl_lookup_single() enforces
this:
- A lookup in a directory that does not match fails with -ESTALE.
- A lookup of the directory itself fails with -EREMOTE.
ovl_fileattr_set() copies the directory up, which creates it in the
upper layer if it only existed in a lower layer. It then passes
FS_CASEFOLD_FL on to the upper filesystem. The upper filesystem accepts
the change if the upper directory is empty, regardless of what the
merged directory contains. The merged directory is the one that the user
sees, with the names from the upper and the lower directories.
After the change the upper directory no longer matches the mount. If the
directory is the root of the overlay, the whole mount is affected.
The flag can also change without chattr +F or -F. chattr reads all flags
of a directory, changes one and writes all of them back. For a directory
that only exists in a lower layer, overlayfs reads the flags from the
lower filesystem. xfs with the ascii-ci feature reports FS_CASEFOLD_FL
on every inode, but never sets S_CASEFOLD, the inode flag that overlayfs
compares with the mount. So its directories count as not casefolded.
With a lower layer on such an xfs and an upper layer on ext4 with the
casefold feature, chattr +A on a lower-only directory therefore sets
FS_CASEFOLD_FL on the new, empty upper directory.
Reproduced as root on tmpfs and on ext4 with chattr +F or -F on an
overlay directory whose upper directory was empty. Afterwards lookups
below it failed with ESTALE, and lookups of the directory itself failed
with EREMOTE. The chattr +A case was seen once, on a kernel with an
earlier form of this patch that still passed the caller's flag on:
lookups of the directory failed with EREMOTE.
Fix this by returning -EOPNOTSUPP if FS_IOC_SETFLAGS, the only call that
can change the flag, asks for a casefold flag on a directory that does
not agree with the casefold state of the mount. This also refuses the
chattr +A case above.
[amir: check the flag against the casefold state of the mount instead of
reading back the flags] |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Avoid closing unowned DDC pins
[WHY]
dal_ddc_open() cleans up pins it acquires on later failures. If the
data-pin open fails, this attempt acquired nothing. If opening the
clock pin or configuring fails, dal_ddc_open() closes the pins it
opened. An extra dal_ddc_close() is unnecessary and unsafe:
GPIO_RESULT_ALREADY_OPENED can mean AUX owns the existing handles,
and closing them here would disrupt AUX.
[HOW]
Remove the extra dal_ddc_close() from the failed-open path.
(cherry picked from commit 175ae7772b68757b4932f34ff862923cab7abe21) |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: caiaq: free the EP4 URB when input setup fails
The three controllers that use the EP4 input URB allocate it before
checking the endpoint type and before registering the input device. On
failure they jump to exit_free_idev, which clears cdev->input_dev but
leaves cdev->ep4_in_urb set. The card teardown then calls
snd_usb_caiaq_input_free(), which returns early because input_dev is
NULL, so the URB is never freed.
Release the URB before dropping the input device on the error path. |