| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: lan966x: restore RX state on reload failure
lan966x_fdma_reload() backs up rx->page_pool and rx->fdma before
reallocating the RX resources for the new MTU. If the allocation fails,
the restore path puts these fields back before restarting RX.
However, the reload path also updates rx->page_order and rx->max_mtu
before calling lan966x_fdma_rx_alloc(). These fields are not restored on
failure, so RX can be restarted with the old pages, old FDMA state and
old page pool, but with the page geometry from the failed new MTU.
This can make the XDP path advertise a frame size derived from the new
page_order while the actual RX pages still come from the old allocation.
For example, after a failed reload to a jumbo MTU, xdp_init_buff() may be
called with a frame size larger than the restored RX pages.
lan966x_fdma_rx_alloc_page_pool() also registers the newly allocated page
pool with each port's XDP RXQ before fdma_alloc_coherent() is called. If
fdma_alloc_coherent() fails, the new page pool is destroyed, but the
rollback path does not restore the per-port XDP RXQ mem model
registration either.
Save and restore rx->page_order and rx->max_mtu, and restore the old page
pool registration for each port's XDP RXQ before RX is started again.
This keeps the restored RX state consistent after a failed reload. |
| Multiple Cisco products are affected by a vulnerability in the Snort 3 SMTP MIME Decoder that could allow an unauthenticated, remote attacker to cause the Snort 3 Detection Engine to restart.
This vulnerability is due to a lack of error checking when the MIME fields of the SMTP header are parsed. An attacker could exploit this vulnerability by sending crafted SMTP packets through an established connection to be parsed by Snort 3. A successful exploit could allow the attacker to cause a denial of service (DoS) condition when the Snort 3 Detection Engine unexpectedly restarts. |
| In the Linux kernel, the following vulnerability has been resolved:
accel/ivpu: Add bounds checks for firmware log indices
Add validation that read and write indices in the firmware log buffer
are within valid bounds (< data_size) before using them. If
out-of-bounds indices are encountered (from firmware), clamp them to
safe values instead of proceeding with invalid offsets.
This prevents potential out-of-bounds buffer access when firmware
supplies invalid log indices. |
| F´ (F Prime) is a framework that enables development and deployment of spaceflight and other embedded software applications. Prior to 4.3.0, Svc::TlmPacketizer TlmRecv_handler fixed-slot copy TlmRecv_handler copies val.getSize bytes into entry.channelSize storage without confirming that the runtime value fits. When a telemetry update for a configured channel carries a serialized value larger than that channel fixed slot, the copy overwrites adjacent channel fields and causes corrupted packetized telemetry to be emitted. This issue is fixed in version 4.3.0. |
| AMI APTIOV contains vulnerabilities
in BIOS where users may cause “Buffer Access with Incorrect Length
Value” by local access. Successful exploitation of this vulnerability could
lead to buffer overflows, memory corruption, and arbitrary code execution, and
also impact Confidentiality, Integrity, and Availability. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: target: iscsi: Validate CHAP_R length before base64 decode
chap_server_compute_hash() allocates client_digest as
kzalloc(chap->digest_size) and then, for BASE64-encoded responses,
passes chap_r directly to chap_base64_decode() without checking whether
the input length could produce more than digest_size bytes of output.
chap_base64_decode() writes to the destination unconditionally as long
as there is input to consume. With MAX_RESPONSE_LENGTH set to 128 and
the "0b" prefix stripped by extract_param(), up to 127 base64 characters
can reach the decoder. 127 characters decode to 95 bytes. For SHA-256
(digest_size=32) this overflows client_digest by 63 bytes; for MD5
(digest_size=16) the overflow is 79 bytes.
The length check at line 344 fires after the write has already happened.
The HEX branch in the same switch statement already validates the length
up front. Apply the same approach to the BASE64 branch: strip trailing
base64 padding characters, then reject any input whose data length
exceeds DIV_ROUND_UP(digest_size * 4, 3) before calling the decoder.
Stripping trailing '=' before the comparison handles both padded and
unpadded encodings. chap_base64_decode() already returns early on '=',
so the full original string is still passed to the decoder unchanged.
The mutual CHAP path decodes CHAP_C into initiatorchg_binhex, which is
kzalloc(CHAP_CHALLENGE_STR_LEN). extract_param() caps initiatorchg at
CHAP_CHALLENGE_STR_LEN characters, so at most CHAP_CHALLENGE_STR_LEN-1
base64 characters reach the decoder. The maximum decoded size,
DIV_ROUND_UP((CHAP_CHALLENGE_STR_LEN-1) * 3, 4), is less than
CHAP_CHALLENGE_STR_LEN, so no overflow is possible there. A comment is
added at the call site to document this. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: validate cookie AUTH state before use
When cookie authentication is disabled, COOKIE_ECHO restores fixed-size
AUTH fields directly from peer-controlled cookie bytes. A forged RANDOM
length, HMAC list, or CHUNKS list can then reach association consumers
with lengths or identifiers that were never validated against the local
backing arrays.
A forged RANDOM length can cause out-of-bounds reads during key-vector
construction. A forged HMAC identifier also caused a 32-byte write past
a zero-length AUTH chunk, providing a primitive for a local privilege
escalation chain.
Validate the cookie's RANDOM, HMACS, and CHUNKS parameters at the cookie
trust boundary before copying them into the association. Reject invalid
types, malformed lengths, unsupported HMAC identifiers, HMAC lists
without SHA1, and forbidden chunk ids. |
| In the Linux kernel, the following vulnerability has been resolved:
bnxt_en: Disable EOP for TPA on all chips to prevent data corruption
EOP (End of frame padding) on the AGG ring may cause overlapping of
zero padding at the end of one segment with the next segment's data.
If Relaxed Ordering (RO) is enabled, the zero padding may overwrite
valid data in the next segment and corrupt the data. Older chips
(P5 and older) do not automatically disable RO when EOP is enabled.
On some ARM systems, data corruption was reported on 57508 (P5)
chips with RO enabled.
Always disable EOP on all chips on the AGG rings when TPA is enabled
to fix the data corruption. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/bnxt_re: Add a max slot check for SQ
The variable WQE mode must be validated against
the maximum slots supported by HW. The max supported
value is 64K. Adding a max and min check and fail if user
supplied value is more than the max supported and zero. |
| In the Linux kernel, the following vulnerability has been resolved:
netfs: Fix zeropoint update where i_size > remote_i_size
Fix the update of the zero point[*] by netfs_release_folio() when there is
uncommitted data in the pagecache beyond the folio being released but the
on-server EOF is in this folio (ie. i_size > remote_i_size). The update
needs to limit zero_point to remote_i_size, not i_size as i_size is a local
phenomenon reflecting updates made locally to the pagecache, not stuff
written to the server. remote_i_size tracks the server's i_size.
[*] The zero point is the file position from which we can assume that the
server will just return zeros, so we can avoid generating reads.
Note that netfs_invalidate_folio() probably doesn't need fixing as
zero_point should be updated by setattr after truncation or fallocate.
Found with:
fsx -q -N 1000000 -p 10000 -o 128000 -l 600000 \
/xfstest.test/junk --replay-ops=junk.fsxops
using the following as junk.fsxops:
truncate 0x0 0x1bbae 0x82864
write 0x3ef2e 0xf9c8 0x1bbae
write 0x67e05 0xcb5a 0x4e8f6
mapread 0x57781 0x85b6 0x7495f
copy_range 0x5d3d 0x10329 0x54fac 0x7495f
write 0x64710 0x1c2b 0x7495f
mapread 0x64000 0x1000 0x7495f
on cifs with the default cache option.
It shows read-gaps on folio 0x64 failing with a short read (ie. it hits
EOF) if the FMODE_READ check is commented out in netfs_perform_write():
if (//(file->f_mode & FMODE_READ) ||
netfs_is_cache_enabled(ctx)) {
and no fscache. This was initially found with the generic/522 xfstest. |
| In the Linux kernel, the following vulnerability has been resolved:
espintcp: use sk_msg_free_partial to fix partial send
sk_msg_free_partial() ensures consistency of the skmsg at every
iteration, without having to manually handle uncharges and offsets.
This simplifies the code, and fixes some bugs in skmsg accounting when
we don't send the full contents. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: cyw: fix heap overflow on a short auth frame
brcmf_notify_auth_frame_rx() takes the frame length from the firmware
event and copies the frame body with the management header offset
subtracted:
u32 mgmt_frame_len = e->datalen - sizeof(struct brcmf_rx_mgmt_data);
...
memcpy(&mgmt_frame->u, frame,
mgmt_frame_len - offsetof(struct ieee80211_mgmt, u));
The only length check is e->datalen >= sizeof(*rxframe), so mgmt_frame_len
can be anything from 0 up. offsetof(struct ieee80211_mgmt, u) is 24. When
mgmt_frame_len is below that, the subtraction wraps as an unsigned value to
a huge length. The memcpy then runs far past the kzalloc'd buffer. A
malicious or malfunctioning AP can make the frame short during the
external SAE auth exchange, so this is a remotely triggered heap overflow.
Reject frames shorter than the management header offset before the copy. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btrtl: validate firmware patch bounds
rtlbt_parse_firmware() copies patch_length - 4 bytes before appending the
firmware version. A malformed firmware patch shorter than the version field
can make this subtraction underflow and turn the copy into an oversized
read and write during Bluetooth setup.
The existing patch_offset + patch_length check can also wrap on 32-bit
architectures. Validate the patch length and range without arithmetic
overflow before allocating or copying the patch. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/zcrypt: Validate length for CCA ECC private key requests
cca_ecc2protkey() derives the copy length for the CPRB parameter
block directly from the length field in the key token. Reject the
request early if the token length exceeds the available space in the
parameter block. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/vmwgfx: Validate vmw_surface_metadata::array_size
This field comes from userspace and should be validated against specific
limits depending on which Shader Model (SM) is available. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath6kl: fix OOB read from firmware IE lengths in connect event
The firmware-controlled beacon_ie_len, assoc_req_len, and assoc_resp_len
fields in ath6kl_wmi_connect_event_rx() are not validated against the
buffer length. Their sum (up to 765) can exceed the actual WMI event
data, causing out-of-bounds reads during IE parsing and state corruption
of wmi->is_wmm_enabled.
Add a check that the total IE length fits within the buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: validate DFS referral PathConsumed
parse_dfs_referrals() validates that the response contains the fixed
referral entry array and, on for-next, the per-referral string offsets.
However, the response also contains a PathConsumed value that is later
used for DFS path parsing.
If a malformed response provides a PathConsumed value larger than the
search name, later DFS parsing can advance beyond the end of the path.
Validate PathConsumed against the search name length before storing it in
the parsed referral. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/pkey: Check length in PKEY_VERIFYPROTK ioctl
Explicitly check the buffer length request structure provided by
user-space and fail, if it exceeds the buffer size. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: L2CAP: validate option length before reading conf opt value
l2cap_get_conf_opt() derives the option length from the
attacker-controlled opt->len field and immediately dereferences
opt->val (as u8, get_unaligned_le16() or get_unaligned_le32(), or a
raw pointer for the default case) before any caller has confirmed
that opt->len bytes are present in the buffer. The callers
(l2cap_parse_conf_req(), l2cap_parse_conf_rsp() and
l2cap_conf_rfc_get()) only detect a malformed option afterwards, once
the running length has gone negative, by which point the
out-of-bounds read has already executed.
An existing post-hoc length check keeps the garbage value from being
consumed, so this is not a data leak in the current control flow. It
is still a validate-after-use ordering bug: up to 4 bytes are read
past the end of the buffer before it is known to contain them, and it
is fragile to future changes in the callers.
Fix it at the source. Pass the end of the buffer into
l2cap_get_conf_opt() and refuse to touch opt->val unless the full
option (header + value) fits. Each caller computes an end pointer
once before the loop and checks the return value directly instead of
inferring the error from a negative length. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv4: raw: reject IP_HDRINCL packets with ihl < 5
raw_send_hdrinc() validates that the caller-supplied IPv4 header
fits within the message length:
iphlen = iph->ihl * 4;
err = -EINVAL;
if (iphlen > length)
goto error_free;
if (iphlen >= sizeof(*iph)) {
/* fix up saddr, tot_len, id, csum, transport_header */
}
It does not, however, reject ihl < 5. For such a packet the
"if (iphlen >= sizeof(*iph))" branch is skipped, leaving the
crafted iphdr untouched, but the packet is still handed to
__ip_local_out() and onward. Downstream consumers that read
iph->ihl assume a sane value: net/ipv4/ah4.c:ah_output() in
particular subtracts sizeof(struct iphdr) from top_iph->ihl * 4
and passes the (signed-int-negative, then cast to size_t)
result to memcpy(), producing an OOB access of length close to
SIZE_MAX and a host kernel panic.
An IPv4 header with ihl < 5 is malformed by definition (RFC 791:
"Internet Header Length is the length of the internet header in
32 bit words ... Note that the minimum value for a correct header
is 5."). The kernel should not be willing to inject such a
packet into its own output path.
Reject "iphlen < sizeof(*iph)" alongside the existing
"iphlen > length" check. This matches the principle that locally
constructed packets that re-enter the IP stack must pass the same
basic sanity tests that a foreign packet would be subjected to.
Once this lands, the "if (iphlen >= sizeof(*iph))" wrapper around
the fixup branch becomes redundant; left in place to keep the
patch minimal and backport-friendly. A follow-up can unwrap it.
Note that commit 86f4c90a1c5c ("ipv4, ipv6: ensure raw socket
message is big enough to hold an IP header") ensures the message
buffer is large enough to hold an iphdr, but does not constrain
the self-reported iph->ihl.
Reachability: the malformed packet source is any caller with
CAP_NET_RAW, including an unprivileged process in a user+net
namespace on a kernel with CONFIG_USER_NS=y. The reproduced AH
crash also requires a matching xfrm AH policy on the outgoing
route; a container granted CAP_NET_ADMIN can install that state
and policy in its netns. Loopback bypasses xfrm_output, so the
trigger uses a real netdev.
Reproduced on UML + KASAN: kernel-mode fault at addr 0x0 with
memcpy_orig at the crash site. Same shape reproduces inside a
rootless Docker container with --cap-add NET_ADMIN on a stock
distro kernel. |