| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Unlink NVMe unsol ctx before freeing on LS reject error
qla_nvme_xmt_ls_rsp() obtains uctx, which was linked into
fcport->unsol_ctx_head by qla2xxx_process_purls_iocb() and is still linked
when the NVMe transport calls back to transmit the LS response. On the
error (out:) path the function frees uctx with kfree() but never removes
it from the list. This leaves a freed node in fcport->unsol_ctx_head: the
next list_add_tail() for that fcport writes through the freed node, and a
subsequent list_del() can corrupt the list or panic.
Unlink uctx with list_del() before kfree() on the error path, matching the
other free sites in qla_nvme_release_lsrsp_cmd_kref() and
qla2xxx_process_purls_pkt(). qla2x00_rel_sp() in the failure path only
returns the SRB to its pool and does not invoke sp->put_fn, so the out:
path is the sole free and uctx is always still linked there. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: don't call ieee80211_handle_reconfig_failure when not needed
In case reconfiguration of NAN fails, we call
ieee80211_handle_reconfig_failure, that marks all interfaces as not in
the driver.
Then, at the error path of the reconfig, cfg80211_shutdown_all_interfaces
is called to destroy all the interfaces.
If we have any other interface but the NAN one, for example a BSS
station, then when its state (links, stations) will be removed, we
won't tell the driver about this, because we will think that the
interfaces are not in the driver, and then drivers might remain with
dangling pointers to objects like stations and links (at least for
iwlwifi this is the case).
ieee80211_handle_reconfig_failure is meant to be called after we cleaned
up the state in the driver, there is no reason to call it for NAN
reconfiguration failure.
Fix the code to just warn in such a case, as we do in other error paths
in reconfig where it is too complicated to rewind. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: mvm: fix P2P-Device binding handling
Our binding handling for P2P-Device can run into the following
scenario, as observed by our testing:
- a station interface is connected on some channel
- the P2P-Device does a remain-on-channel (ROC) on that channel
- the ROC ends, and the P2P-Device is removed from the binding,
but the phy_ctxt pointer is left around as a PHY cache so we
don't need to recalibrate to the channel again and again in
case it's not shared
- a binding update by the station interface, even a removal,
will re-add the P2P-Device to the binding
- the P2P-Device is removed, which removes the PHY context, but
it's still in the binding so the firmware crashes
Since the P2P device is removed from the binding and only re-
added by unrelated code, but we want to keep the phy_ctxt around
as a cache for future ROC usage, fix it by adding a boolean that
indicates whether or not the P2P-Device should be added to the
binding, and handle that in the binding iterator. That way, the
station interface cannot re-add the P2P-Device to the binding
when that isn't active. |
| In the Linux kernel, the following vulnerability has been resolved:
pds_core: quiesce DMA before freeing resources
pdsc_teardown() frees DMA buffers but does not disable bus mastering,
leaving the device able to perform DMA after the buffers are freed.
This can lead to use-after-free if the device writes to freed memory.
Add pci_clear_master() to pdsc_teardown() to disable bus mastering
before freeing resources, ensuring all DMA is quiesced.
Add pci_set_master() to pdsc_setup() to re-enable bus mastering,
which is needed for the firmware recovery path since pdsc_teardown()
now disables it. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: ISO: fix race of kfree vs kref_get_unless_zero
hci_conn::iso_data is accessed and modified without lock or RCU.
This leads to a race
[Task hdev->workqueue] [Task 2]
iso_recv iso_conn_put(conn)
conn = LOAD hcon->iso_data iso_conn_free(conn)
iso_conn_hold_unless_zero(conn) hcon->iso_data = NULL
kfree(conn)
kref_get_unless_zero(&conn->ref) /* UAF */
and also to races in iso_conn_add() vs. iso_conn_free().
Fix by adding spinlock hci_conn::proto_lock and using it to guard
hci_conn::iso_data. |
| In the Linux kernel, the following vulnerability has been resolved:
dibs: fix use-after-free of dmb_node in loopback attach/detach/unregister
dibs_lo_attach_dmb(), dibs_lo_detach_dmb() and dibs_lo_unregister_dmb()
look up the dmb_node under dmb_ht_lock, drop the lock and only then
operate on the node's refcount. Nothing keeps the node alive across
that window: __dibs_lo_unregister_dmb() removes the node from the hash
table under the write lock and immediately frees it.
A concurrent final put can therefore free the node between the lookup
and the refcount operation:
CPU0 (attach) CPU1 (owner unregisters)
read_lock_bh(&dmb_ht_lock)
find dmb_node (refcnt == 1)
read_unlock_bh(&dmb_ht_lock)
refcount_dec_and_test() 1 -> 0
write_lock_bh(&dmb_ht_lock)
hash_del(&dmb_node->list)
write_unlock_bh(&dmb_ht_lock)
kfree(dmb_node)
refcount_inc_not_zero(&dmb_node->refcnt) <-- use-after-free
The same window exists for the refcount_dec_and_test() calls in the
detach and unregister paths.
Close the race structurally by making hash table membership and the
refcount transitions atomic with respect to each other:
- Perform the final refcount_dec_and_test() and hash_del() in a single
dmb_ht_lock write-side critical section, in both the unregister and
the detach path. Freeing the node still happens after the lock is
dropped, which is safe because a node whose refcount reached zero has
left the hash table and can no longer be found.
- This establishes the invariant that any node found in the hash table
holds at least one reference, and that the final reference can only
be dropped under the write lock. dibs_lo_attach_dmb() can thus take
its reference with a plain refcount_inc() while still holding the
read lock; refcount_inc_not_zero() is no longer needed.
__dibs_lo_unregister_dmb() no longer touches the hash table and is
renamed to dibs_lo_free_dmb() accordingly.
Note: commit cc21191b584c ("dibs: Move data path to dibs layer") moved
the code to its current location; the race was introduced earlier by
commit c3a910f2380f ("net/smc: implement DMB-merged operations of
loopback-ism").
Tested SMC-D via ISM and dibs loopback. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Clear rb node linkage when freeing bpf_rb_root
bpf_rb_root_free() detaches the root by copying the current rb_root_cached
and then replacing the live root with RB_ROOT_CACHED. It then walks the
copied root and drops each object contained in the tree.
This leaves the rb node state intact while dropping the object. If the
object is refcounted and survives the drop, its bpf_rb_node_kern still
contains an owner pointer to the freed root and stale rb tree linkage. If
a later bpf_rb_root allocation reuses the same address, bpf_rbtree_remove()
can incorrectly pass the owner check and call rb_erase_cached() on a node
whose rb pointers belong to the old tree.
Mirror the list draining behavior by marking nodes as busy while the root
is being detached, then clear the rb node and release the owner before
dropping the containing object. This makes surviving nodes unowned and
safe to reject from remove or accept for a later add. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/bnxt_re: Free CQ toggle page after firmware teardown
Free the toggle page only after firmware teardown completes so that
an NQ interrupt arriving during bnxt_qplib_destroy_cq() won't write
the toggle value to an already-freed page. Move free_page() after
bnxt_qplib_destroy_cq. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sync: extend conn_hash lookup critical sections
Using RCU-protected pointers outside the critical sections without
refcount is incorrect and may result to UAF.
Extend critical section to cover both hci_conn_hash lookup and use of
the returned conn.
Add surrounding rcu_read_lock() also when return value is not used, in
preparation for RCU lockdep requirement to hci_lookup_le_connect().
This avoids concurrent deletion of the conn before we are done
dereferencing it.
Also, make sure to hold hdev->lock when accessing hdev->accept_list. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/guc: Keep scheduler timeline name alive
The scheduler keeps a pointer to the timeline name, but q->name
is freed with the exec queue while scheduler fences can still
reference it.
Store the name in struct xe_guc_exec_queue so it shares
the scheduler's RCU-deferred lifetime.
(cherry picked from commit 41075f0eb5dcbd3b065d15f15ef7bbe9315188e8) |
| In the Linux kernel, the following vulnerability has been resolved:
pds_core: fix use-after-free on workqueue during remove
In pdsc_remove(), the workqueue is destroyed before pdsc_teardown()
is called. This ordering allows two paths to queue work on the
destroyed workqueue:
1. If pdsc_teardown() -> pdsc_devcmd_reset() times out, the error
path in pdsc_devcmd_locked() queues health_work.
2. A NotifyQ event can trigger the ISR and queue work before free_irq()
is called in pdsc_teardown().
Fix by moving destroy_workqueue() after pdsc_teardown() so the
workqueue outlives every queuer; destroy_workqueue() then flushes any
work still pending.
Draining the queued work also requires ordering the teardown so the
resources that work touches are freed last:
- In pdsc_qcq_free(), after freeing the interrupt, cancel_work_sync()
the queue's work and only then clear qcq->intx, so
pdsc_process_adminq()'s read of qcq->intx for interrupt-credit
return cannot race with the clear.
- Free adminqcq before notifyqcq: the shared adminq ISR is released
when adminqcq is freed, and the adminq work accesses notifyqcq, so
both must be stopped before notifyqcq is freed. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: capture fast-RX rate before mesh reuses skb->cb
ieee80211_invoke_fast_rx() reads RX status through
IEEE80211_SKB_RXCB(skb), which aliases the same skb->cb storage
that ieee80211_rx_mesh_data() reuses as IEEE80211_TX_INFO. In the
unicast forward path, mesh_data does:
info = IEEE80211_SKB_CB(fwd_skb);
memset(info, 0, sizeof(*info));
on the same skb the caller still names via rx->skb, then either
queues the skb for TX (success) or kfree_skb()'s it (no-route)
before returning RX_QUEUED. The caller's RX_QUEUED arm then
calls sta_stats_encode_rate(status) on memory that is either
zeroed (success path) or freed (no-route path). The latter is
KASAN slab-use-after-free in ieee80211_prepare_and_rx_handle.
Fix by encoding the rate from status before invoking
ieee80211_rx_mesh_data(), so the RX_QUEUED arm consumes a value
captured while status was still backed by valid memory. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: pcm: oss: Fix setup list UAF on proc write error
snd_pcm_oss_proc_write() links a newly allocated setup entry into the
OSS setup list before duplicating the task name. If the task-name
allocation fails, the error path frees the already linked entry and
leaves setup_list pointing at freed memory.
A later OSS device open can then walk the stale list entry in
snd_pcm_oss_look_for_setup() and dereference freed memory.
Allocate the task name and initialize the setup entry before publishing
the entry on setup_list. Also fetch the initial proc read iterator only
after taking setup_mutex, so all setup_list traversal follows the same
list lifetime rules. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: universal-pidff: stop the device when force-feedback init fails
universal_pidff_probe() starts the device with hid_hw_start() and then, if
force-feedback initialisation fails, returns the error through a label that
only does "return error". The device is left started.
The HID core does not unwind on the driver's behalf. __hid_device_probe()
releases the devres group, closes the report and clears hdev->driver:
if (ret) {
devres_release_group(&hdev->dev, hdev->devres_group_id);
hid_close_report(hdev);
hdev->driver = NULL;
}
The hidraw character device that hid_hw_start() registered through
hid_connect() is allocated with kzalloc() and added with cdev_device_add(),
so it is not devres-managed and survives that. With hdev->driver NULL,
hid_device_remove() skips hid_hw_stop() as well, because it only unwinds
while a driver is still attached. The registration therefore outlives the
device on both paths.
Opening the surviving /dev/hidrawX writes into freed memory. KASAN reports
a use-after-free write from hidraw_open() -> hid_hw_open() -> the
transport's open callback, which takes a spinlock inside the freed object.
A descriptor that carries a PID usage page and no input reports is enough:
hidraw claims the device so hid_hw_start() succeeds, while hid->inputs
stays empty so force-feedback init fails. The other failure returns in
hid_pidff_init_with_quirks() - no output reports, an allocation failure,
pidff_init_fields(), pidff_check_autocenter(), an unusable effect count,
input_ff_create() - all reach the same label.
Stop the device on that path. hid-dr.c and hid-emsff.c, which start the
device with the same HID_CONNECT_DEFAULT & ~HID_CONNECT_FF mask, already do
this. The two earlier gotos must keep returning without hid_hw_stop(),
since neither has a started device, so give the path that fails after the
start its own label.
Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com> |
| In the Linux kernel, the following vulnerability has been resolved:
svcrdma: Clear sc_cm_id when ADDR_CHANGE replacement fails
When svc_rdma_listen_handler() handles RDMA_CM_EVENT_ADDR_CHANGE,
it creates a replacement listener cm_id and returns 1, telling
the CM core to destroy the old one. If the replacement allocation
fails, sc_cm_id still points at the old cm_id that the CM core is
about to destroy. Any subsequent dereference of sc_cm_id --
such as svc_rdma_detach()'s rdma_disconnect() call -- is a
use-after-free.
NULL sc_cm_id on the failure path and guard svc_rdma_detach()'s
rdma_disconnect() call against NULL so that the listener can
be torn down safely when the server shuts down. |
| In the Linux kernel, the following vulnerability has been resolved:
power: supply: qcom_battmgr: fix use-after-free
qcom_battmgr_pdr_notify() queues enable_work when the PMIC GLINK service
comes up, and the worker recovers battmgr through container_of() to issue
firmware requests. The PMIC GLINK client stays on the client list until
its devres release action runs, so a PDR notification can keep queueing
the work, and a pending or running worker can access battmgr after devres
frees it.
Make enable_work device-managed with devm_work_autocancel(), registered
before the PMIC GLINK client is allocated. The devres cleanup then
releases the client first, so no further notification can queue the work,
and cancels the work before battmgr is freed.
This issue was found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
net/smc: fix UAF on lgr list traversal in smcr_port_err()
smcr_port_err() traverses smc_lgr_list.list without holding
smc_lgr_list.lock, allowing a concurrent smc_lgr_terminate_sched()
to free an lgr while it is still being dereferenced.
Hold smc_lgr_list.lock across the traversal. Update
smc_ib_gid_check() to call smcr_port_err() after releasing the lock. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Reject pkt arguments in mutating subprogs
The verifier tracks changes in how PTR_TO_PACKET registers'
bounds are modified across subprog boundaries. PTR_TO_PACKET
registers are actually passed as PTR_TO_MEM, which is assumed
valid for the entire call. This is not the case with packet memory,
where a pskb_* call may invalidate its memory region.
Reject BPF code that passes PTR_TO_PACKET pointers to subprogs that
may mutate a packet. We cannot pass the pointer as a true PTR_TO_PACKET
because we would also need to somehow pass the PTR_TO_PACKET_META
or PTR_TO_PACKET_END to the subprog. Since we cannot avoid representing
the pointer in the subprog as PTR_TO_MEM, only permit it if the
subprog is guaranteed not to mutate the packet. |
| In the Linux kernel, the following vulnerability has been resolved:
net: bcmgenet: stop Tx NAPI before disabling the queues
bcmgenet_netif_stop() and the Wake-on-LAN branch of bcmgenet_suspend()
both disable the Tx queues first and stop Tx NAPI several steps later. A
completion in flight calls netif_tx_wake_queue() in between, and nothing
stops the queue again, so a transmit can reach the rings after they have
been freed.
Close is safe because dev_deactivate_many() stops the qdisc first.
bcmgenet_suspend() does not, so stop Tx NAPI before the queues on both
paths.
KASAN on a Raspberry Pi CM4, driven from an MTU change because suspend
freezes user space before the callback runs:
BUG: KASAN: use-after-free in bcmgenet_xmit+0x17f8/0x2258
Write of size 8 at addr ffffff8055844a68 by task ksoftirqd/0/14
bcmgenet_xmit+0x17f8/0x2258
dev_hard_start_xmit+0x13c/0x588
sch_direct_xmit+0x108/0x340
__dev_queue_xmit+0x1190/0x3848 |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: llcp: Fix race condition in accept_queue lifecycle
In nfc_llcp_socket_release(), sockets and listener accept queues are
walked under the local sockets rwlock and bh_lock_sock(). However,
bh_lock_sock() does not synchronise against process-context lock_sock()
held by nfc_llcp_accept_dequeue() during accept(). Because
socket_release() does not check sock_owned_by_user(), both paths can
concurrently unlink and release the same child socket, resulting in
use-after-free or a NULL pointer dereference of child->parent in
nfc_llcp_accept_unlink().
Fix this synchronisation race by having nfc_llcp_socket_release() use
process-context lock_sock() instead of bh_lock_sock():
1. Pop sockets from the local sockets list under the write lock using
nfc_llcp_sock_list_pop() so lock_sock() can be acquired without
holding the rwlock.
2. Because lock_sock() can sleep, defer the final release of the
nfc_llcp_local structure to a workqueue (release_work). This avoids
a sleeping-in-atomic bug when the last local reference is dropped
from softirq context. Additionally, hold a single device reference
on local from registration until final destruction.
3. In nfc_llcp_local_get(), use kref_get_unless_zero() to prevent
resurrecting a local object whose teardown has been scheduled.
4. In llcp_sock_accept(), verify that the listener socket state is still
LLCP_LISTEN after waking from schedule_timeout() to prevent hangs if
the listener is closed concurrently.
5. When unlinking unaccepted child sockets during listener release,
unlink them from local->sockets, call sock_orphan(), and drop their
initial sk_alloc creation reference via sock_put().
6. Make nfc_llcp_accept_unlink() idempotent by guarding parent access with
a NULL check. |