| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
igc: fix PTM cycle trigger logic
Writing to clear the PTM status 'valid' bit while the PTM cycle is
triggered results in unreliable PTM operation. To fix this, clear the
PTM 'trigger' and status after each PTM transaction.
The issue can be reproduced with the following:
$ sudo phc2sys -R 1000 -O 0 -i tsn0 -m
Note: 1000 Hz (-R 1000) is unrealistically large, but provides a way to
quickly reproduce the issue.
PHC2SYS exits with:
"ioctl PTP_OFFSET_PRECISE: Connection timed out" when the PTM transaction
fails
This patch also fixes a hang in igc_probe() when loading the igc
driver in the kdump kernel on systems supporting PTM.
The igc driver running in the base kernel enables PTM trigger in
igc_probe(). Therefore the driver is always in PTM trigger mode,
except in brief periods when manually triggering a PTM cycle.
When a crash occurs, the NIC is reset while PTM trigger is enabled.
Due to a hardware problem, the NIC is subsequently in a bad busmaster
state and doesn't handle register reads/writes. When running
igc_probe() in the kdump kernel, the first register access to a NIC
register hangs driver probing and ultimately breaks kdump.
With this patch, igc has PTM trigger disabled most of the time,
and the trigger is only enabled for very brief (10 - 100 us) periods
when manually triggering a PTM cycle. Chances that a crash occurs
during a PTM trigger are not 0, but extremely reduced. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/core: Silence oversized kvmalloc() warning
syzkaller triggered an oversized kvmalloc() warning.
Silence it by adding __GFP_NOWARN.
syzkaller log:
WARNING: CPU: 7 PID: 518 at mm/util.c:665 __kvmalloc_node_noprof+0x175/0x180
CPU: 7 UID: 0 PID: 518 Comm: c_repro Not tainted 6.11.0-rc6+ #6
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
RIP: 0010:__kvmalloc_node_noprof+0x175/0x180
RSP: 0018:ffffc90001e67c10 EFLAGS: 00010246
RAX: 0000000000000100 RBX: 0000000000000400 RCX: ffffffff8149d46b
RDX: 0000000000000000 RSI: ffff8881030fae80 RDI: 0000000000000002
RBP: 000000712c800000 R08: 0000000000000100 R09: 0000000000000000
R10: ffffc90001e67c10 R11: 0030ae0601000000 R12: 0000000000000000
R13: 0000000000000000 R14: 00000000ffffffff R15: 0000000000000000
FS: 00007fde79159740(0000) GS:ffff88813bdc0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020000180 CR3: 0000000105eb4005 CR4: 00000000003706b0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
ib_umem_odp_get+0x1f6/0x390
mlx5_ib_reg_user_mr+0x1e8/0x450
ib_uverbs_reg_mr+0x28b/0x440
ib_uverbs_write+0x7d3/0xa30
vfs_write+0x1ac/0x6c0
ksys_write+0x134/0x170
? __sanitizer_cov_trace_pc+0x1c/0x50
do_syscall_64+0x50/0x110
entry_SYSCALL_64_after_hwframe+0x76/0x7e |
| In the Linux kernel, the following vulnerability has been resolved:
spi: fsl-qspi: use devm function instead of driver remove
Driver use devm APIs to manage clk/irq/resources and register the spi
controller, but the legacy remove function will be called first during
device detach and trigger kernel panic. Drop the remove function and use
devm_add_action_or_reset() for driver cleanup to ensure the release
sequence.
Trigger kernel panic on i.MX8MQ by
echo 30bb0000.spi >/sys/bus/platform/drivers/fsl-quadspi/unbind |
| In the Linux kernel, the following vulnerability has been resolved:
jbd2: remove wrong sb->s_sequence check
Journal emptiness is not determined by sb->s_sequence == 0 but rather by
sb->s_start == 0 (which is set a few lines above). Furthermore 0 is a
valid transaction ID so the check can spuriously trigger. Remove the
invalid WARN_ON. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/tegra241-cmdqv: Fix warnings due to dmam_free_coherent()
Two WARNINGs are observed when SMMU driver rolls back upon failure:
arm-smmu-v3.9.auto: Failed to register iommu
arm-smmu-v3.9.auto: probe with driver arm-smmu-v3 failed with error -22
------------[ cut here ]------------
WARNING: CPU: 5 PID: 1 at kernel/dma/mapping.c:74 dmam_free_coherent+0xc0/0xd8
Call trace:
dmam_free_coherent+0xc0/0xd8 (P)
tegra241_vintf_free_lvcmdq+0x74/0x188
tegra241_cmdqv_remove_vintf+0x60/0x148
tegra241_cmdqv_remove+0x48/0xc8
arm_smmu_impl_remove+0x28/0x60
devm_action_release+0x1c/0x40
------------[ cut here ]------------
128 pages are still in use!
WARNING: CPU: 16 PID: 1 at mm/page_alloc.c:6902 free_contig_range+0x18c/0x1c8
Call trace:
free_contig_range+0x18c/0x1c8 (P)
cma_release+0x154/0x2f0
dma_free_contiguous+0x38/0xa0
dma_direct_free+0x10c/0x248
dma_free_attrs+0x100/0x290
dmam_free_coherent+0x78/0xd8
tegra241_vintf_free_lvcmdq+0x74/0x160
tegra241_cmdqv_remove+0x98/0x198
arm_smmu_impl_remove+0x28/0x60
devm_action_release+0x1c/0x40
This is because the LVCMDQ queue memory are managed by devres, while that
dmam_free_coherent() is called in the context of devm_action_release().
Jason pointed out that "arm_smmu_impl_probe() has mis-ordered the devres
callbacks if ops->device_remove() is going to be manually freeing things
that probe allocated":
https://lore.kernel.org/linux-iommu/20250407174408.GB1722458@nvidia.com/
In fact, tegra241_cmdqv_init_structures() only allocates memory resources
which means any failure that it generates would be similar to -ENOMEM, so
there is no point in having that "falling back to standard SMMU" routine,
as the standard SMMU would likely fail to allocate memory too.
Remove the unwind part in tegra241_cmdqv_init_structures(), and return a
proper error code to ask SMMU driver to call tegra241_cmdqv_remove() via
impl_ops->device_remove(). Then, drop tegra241_vintf_free_lvcmdq() since
devres will take care of that. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/vmscan: don't try to reclaim hwpoison folio
Syzkaller reports a bug as follows:
Injecting memory failure for pfn 0x18b00e at process virtual address 0x20ffd000
Memory failure: 0x18b00e: dirty swapcache page still referenced by 2 users
Memory failure: 0x18b00e: recovery action for dirty swapcache page: Failed
page: refcount:2 mapcount:0 mapping:0000000000000000 index:0x20ffd pfn:0x18b00e
memcg:ffff0000dd6d9000
anon flags: 0x5ffffe00482011(locked|dirty|arch_1|swapbacked|hwpoison|node=0|zone=2|lastcpupid=0xfffff)
raw: 005ffffe00482011 dead000000000100 dead000000000122 ffff0000e232a7c9
raw: 0000000000020ffd 0000000000000000 00000002ffffffff ffff0000dd6d9000
page dumped because: VM_BUG_ON_FOLIO(!folio_test_uptodate(folio))
------------[ cut here ]------------
kernel BUG at mm/swap_state.c:184!
Internal error: Oops - BUG: 00000000f2000800 [#1] SMP
Modules linked in:
CPU: 0 PID: 60 Comm: kswapd0 Not tainted 6.6.0-gcb097e7de84e #3
Hardware name: linux,dummy-virt (DT)
pstate: 80400005 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : add_to_swap+0xbc/0x158
lr : add_to_swap+0xbc/0x158
sp : ffff800087f37340
x29: ffff800087f37340 x28: fffffc00052c0380 x27: ffff800087f37780
x26: ffff800087f37490 x25: ffff800087f37c78 x24: ffff800087f377a0
x23: ffff800087f37c50 x22: 0000000000000000 x21: fffffc00052c03b4
x20: 0000000000000000 x19: fffffc00052c0380 x18: 0000000000000000
x17: 296f696c6f662865 x16: 7461646f7470755f x15: 747365745f6f696c
x14: 6f6621284f494c4f x13: 0000000000000001 x12: ffff600036d8b97b
x11: 1fffe00036d8b97a x10: ffff600036d8b97a x9 : dfff800000000000
x8 : 00009fffc9274686 x7 : ffff0001b6c5cbd3 x6 : 0000000000000001
x5 : ffff0000c25896c0 x4 : 0000000000000000 x3 : 0000000000000000
x2 : 0000000000000000 x1 : ffff0000c25896c0 x0 : 0000000000000000
Call trace:
add_to_swap+0xbc/0x158
shrink_folio_list+0x12ac/0x2648
shrink_inactive_list+0x318/0x948
shrink_lruvec+0x450/0x720
shrink_node_memcgs+0x280/0x4a8
shrink_node+0x128/0x978
balance_pgdat+0x4f0/0xb20
kswapd+0x228/0x438
kthread+0x214/0x230
ret_from_fork+0x10/0x20
I can reproduce this issue with the following steps:
1) When a dirty swapcache page is isolated by reclaim process and the
page isn't locked, inject memory failure for the page.
me_swapcache_dirty() clears uptodate flag and tries to delete from lru,
but fails. Reclaim process will put the hwpoisoned page back to lru.
2) The process that maps the hwpoisoned page exits, the page is deleted
the page will never be freed and will be in the lru forever.
3) If we trigger a reclaim again and tries to reclaim the page,
add_to_swap() will trigger VM_BUG_ON_FOLIO due to the uptodate flag is
cleared.
To fix it, skip the hwpoisoned page in shrink_folio_list(). Besides, the
hwpoison folio may not be unmapped by hwpoison_user_mappings() yet, unmap
it in shrink_folio_list(), otherwise the folio will fail to be unmaped by
hwpoison_user_mappings() since the folio isn't in lru list. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: null - Use spin lock instead of mutex
As the null algorithm may be freed in softirq context through
af_alg, use spin locks instead of mutexes to protect the default
null algorithm. |
| In the Linux kernel, the following vulnerability has been resolved:
virtiofs: add filesystem context source name check
In certain scenarios, for example, during fuzz testing, the source
name may be NULL, which could lead to a kernel panic. Therefore, an
extra check for the source name should be added. |
| In the Linux kernel, the following vulnerability has been resolved:
perf: Fix hang while freeing sigtrap event
Perf can hang while freeing a sigtrap event if a related deferred
signal hadn't managed to be sent before the file got closed:
perf_event_overflow()
task_work_add(perf_pending_task)
fput()
task_work_add(____fput())
task_work_run()
____fput()
perf_release()
perf_event_release_kernel()
_free_event()
perf_pending_task_sync()
task_work_cancel() -> FAILED
rcuwait_wait_event()
Once task_work_run() is running, the list of pending callbacks is
removed from the task_struct and from this point on task_work_cancel()
can't remove any pending and not yet started work items, hence the
task_work_cancel() failure and the hang on rcuwait_wait_event().
Task work could be changed to remove one work at a time, so a work
running on the current task can always cancel a pending one, however
the wait / wake design is still subject to inverted dependencies when
remote targets are involved, as pictured by Oleg:
T1 T2
fd = perf_event_open(pid => T2->pid); fd = perf_event_open(pid => T1->pid);
close(fd) close(fd)
<IRQ> <IRQ>
perf_event_overflow() perf_event_overflow()
task_work_add(perf_pending_task) task_work_add(perf_pending_task)
</IRQ> </IRQ>
fput() fput()
task_work_add(____fput()) task_work_add(____fput())
task_work_run() task_work_run()
____fput() ____fput()
perf_release() perf_release()
perf_event_release_kernel() perf_event_release_kernel()
_free_event() _free_event()
perf_pending_task_sync() perf_pending_task_sync()
rcuwait_wait_event() rcuwait_wait_event()
Therefore the only option left is to acquire the event reference count
upon queueing the perf task work and release it from the task work, just
like it was done before 3a5465418f5f ("perf: Fix event leak upon exec and file release")
but without the leaks it fixed.
Some adjustments are necessary to make it work:
* A child event might dereference its parent upon freeing. Care must be
taken to release the parent last.
* Some places assuming the event doesn't have any reference held and
therefore can be freed right away must instead put the reference and
let the reference counting to its job. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/vf: Don't try to trigger a full GT reset if VF
VFs don't have access to the GDRST(0x941c) register that driver
uses to reset a GT. Attempt to trigger a reset using debugfs:
$ cat /sys/kernel/debug/dri/0000:00:02.1/gt0/force_reset
or due to a hang condition detected by the driver leads to:
[ ] xe 0000:00:02.1: [drm] GT0: trying reset from force_reset [xe]
[ ] xe 0000:00:02.1: [drm] GT0: reset queued
[ ] xe 0000:00:02.1: [drm] GT0: reset started
[ ] ------------[ cut here ]------------
[ ] xe 0000:00:02.1: [drm] GT0: VF is trying to write 0x1 to an inaccessible register 0x941c+0x0
[ ] WARNING: CPU: 3 PID: 3069 at drivers/gpu/drm/xe/xe_gt_sriov_vf.c:996 xe_gt_sriov_vf_write32+0xc6/0x580 [xe]
[ ] RIP: 0010:xe_gt_sriov_vf_write32+0xc6/0x580 [xe]
[ ] Call Trace:
[ ] <TASK>
[ ] ? show_regs+0x6c/0x80
[ ] ? __warn+0x93/0x1c0
[ ] ? xe_gt_sriov_vf_write32+0xc6/0x580 [xe]
[ ] ? report_bug+0x182/0x1b0
[ ] ? handle_bug+0x6e/0xb0
[ ] ? exc_invalid_op+0x18/0x80
[ ] ? asm_exc_invalid_op+0x1b/0x20
[ ] ? xe_gt_sriov_vf_write32+0xc6/0x580 [xe]
[ ] ? xe_gt_sriov_vf_write32+0xc6/0x580 [xe]
[ ] ? xe_gt_tlb_invalidation_reset+0xef/0x110 [xe]
[ ] ? __mutex_unlock_slowpath+0x41/0x2e0
[ ] xe_mmio_write32+0x64/0x150 [xe]
[ ] do_gt_reset+0x2f/0xa0 [xe]
[ ] gt_reset_worker+0x14e/0x1e0 [xe]
[ ] process_one_work+0x21c/0x740
[ ] worker_thread+0x1db/0x3c0
Fix that by sending H2G VF_RESET(0x5507) action instead. |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring/net: fix io_req_post_cqe abuse by send bundle
[ 114.987980][ T5313] WARNING: CPU: 6 PID: 5313 at io_uring/io_uring.c:872 io_req_post_cqe+0x12e/0x4f0
[ 114.991597][ T5313] RIP: 0010:io_req_post_cqe+0x12e/0x4f0
[ 115.001880][ T5313] Call Trace:
[ 115.002222][ T5313] <TASK>
[ 115.007813][ T5313] io_send+0x4fe/0x10f0
[ 115.009317][ T5313] io_issue_sqe+0x1a6/0x1740
[ 115.012094][ T5313] io_wq_submit_work+0x38b/0xed0
[ 115.013223][ T5313] io_worker_handle_work+0x62a/0x1600
[ 115.013876][ T5313] io_wq_worker+0x34f/0xdf0
As the comment states, io_req_post_cqe() should only be used by
multishot requests, i.e. REQ_F_APOLL_MULTISHOT, which bundled sends are
not. Add a flag signifying whether a request wants to post multiple
CQEs. Eventually REQ_F_APOLL_MULTISHOT should imply the new flag, but
that's left out for simplicity. |
| In the Linux kernel, the following vulnerability has been resolved:
tpm: do not start chip while suspended
Checking TPM_CHIP_FLAG_SUSPENDED after the call to tpm_find_get_ops() can
lead to a spurious tpm_chip_start() call:
[35985.503771] i2c i2c-1: Transfer while suspended
[35985.503796] WARNING: CPU: 0 PID: 74 at drivers/i2c/i2c-core.h:56 __i2c_transfer+0xbe/0x810
[35985.503802] Modules linked in:
[35985.503808] CPU: 0 UID: 0 PID: 74 Comm: hwrng Tainted: G W 6.13.0-next-20250203-00005-gfa0cb5642941 #19 9c3d7f78192f2d38e32010ac9c90fdc71109ef6f
[35985.503814] Tainted: [W]=WARN
[35985.503817] Hardware name: Google Morphius/Morphius, BIOS Google_Morphius.13434.858.0 10/26/2023
[35985.503819] RIP: 0010:__i2c_transfer+0xbe/0x810
[35985.503825] Code: 30 01 00 00 4c 89 f7 e8 40 fe d8 ff 48 8b 93 80 01 00 00 48 85 d2 75 03 49 8b 16 48 c7 c7 0a fb 7c a7 48 89 c6 e8 32 ad b0 fe <0f> 0b b8 94 ff ff ff e9 33 04 00 00 be 02 00 00 00 83 fd 02 0f 5
[35985.503828] RSP: 0018:ffffa106c0333d30 EFLAGS: 00010246
[35985.503833] RAX: 074ba64aa20f7000 RBX: ffff8aa4c1167120 RCX: 0000000000000000
[35985.503836] RDX: 0000000000000000 RSI: ffffffffa77ab0e4 RDI: 0000000000000001
[35985.503838] RBP: 0000000000000001 R08: 0000000000000001 R09: 0000000000000000
[35985.503841] R10: 0000000000000004 R11: 00000001000313d5 R12: ffff8aa4c10f1820
[35985.503843] R13: ffff8aa4c0e243c0 R14: ffff8aa4c1167250 R15: ffff8aa4c1167120
[35985.503846] FS: 0000000000000000(0000) GS:ffff8aa4eae00000(0000) knlGS:0000000000000000
[35985.503849] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[35985.503852] CR2: 00007fab0aaf1000 CR3: 0000000105328000 CR4: 00000000003506f0
[35985.503855] Call Trace:
[35985.503859] <TASK>
[35985.503863] ? __warn+0xd4/0x260
[35985.503868] ? __i2c_transfer+0xbe/0x810
[35985.503874] ? report_bug+0xf3/0x210
[35985.503882] ? handle_bug+0x63/0xb0
[35985.503887] ? exc_invalid_op+0x16/0x50
[35985.503892] ? asm_exc_invalid_op+0x16/0x20
[35985.503904] ? __i2c_transfer+0xbe/0x810
[35985.503913] tpm_cr50_i2c_transfer_message+0x24/0xf0
[35985.503920] tpm_cr50_i2c_read+0x8e/0x120
[35985.503928] tpm_cr50_request_locality+0x75/0x170
[35985.503935] tpm_chip_start+0x116/0x160
[35985.503942] tpm_try_get_ops+0x57/0x90
[35985.503948] tpm_find_get_ops+0x26/0xd0
[35985.503955] tpm_get_random+0x2d/0x80
Don't move forward with tpm_chip_start() inside tpm_try_get_ops(), unless
TPM_CHIP_FLAG_SUSPENDED is not set. tpm_find_get_ops() will return NULL in
such a failure case. |
| In the Linux kernel, the following vulnerability has been resolved:
backlight: led_bl: Hold led_access lock when calling led_sysfs_disable()
Lockdep detects the following issue on led-backlight removal:
[ 142.315935] ------------[ cut here ]------------
[ 142.315954] WARNING: CPU: 2 PID: 292 at drivers/leds/led-core.c:455 led_sysfs_enable+0x54/0x80
...
[ 142.500725] Call trace:
[ 142.503176] led_sysfs_enable+0x54/0x80 (P)
[ 142.507370] led_bl_remove+0x80/0xa8 [led_bl]
[ 142.511742] platform_remove+0x30/0x58
[ 142.515501] device_remove+0x54/0x90
...
Indeed, led_sysfs_enable() has to be called with the led_access
lock held.
Hold the lock when calling led_sysfs_disable(). |
| In the Linux kernel, the following vulnerability has been resolved:
watch_queue: fix pipe accounting mismatch
Currently, watch_queue_set_size() modifies the pipe buffers charged to
user->pipe_bufs without updating the pipe->nr_accounted on the pipe
itself, due to the if (!pipe_has_watch_queue()) test in
pipe_resize_ring(). This means that when the pipe is ultimately freed,
we decrement user->pipe_bufs by something other than what than we had
charged to it, potentially leading to an underflow. This in turn can
cause subsequent too_many_pipe_buffers_soft() tests to fail with -EPERM.
To remedy this, explicitly account for the pipe usage in
watch_queue_set_size() to match the number set via account_pipe_buffers()
(It's unclear why watch_queue_set_size() does not update nr_accounted;
it may be due to intentional overprovisioning in watch_queue_set_size()?) |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath12k: Clear affinity hint before calling ath12k_pci_free_irq() in error path
If a shared IRQ is used by the driver due to platform limitation, then the
IRQ affinity hint is set right after the allocation of IRQ vectors in
ath12k_pci_msi_alloc(). This does no harm unless one of the functions
requesting the IRQ fails and attempt to free the IRQ.
This may end up with a warning from the IRQ core that is expecting the
affinity hint to be cleared before freeing the IRQ:
kernel/irq/manage.c:
/* make sure affinity_hint is cleaned up */
if (WARN_ON_ONCE(desc->affinity_hint))
desc->affinity_hint = NULL;
So to fix this issue, clear the IRQ affinity hint before calling
ath12k_pci_free_irq() in the error path. The affinity will be cleared once
again further down the error path due to code organization, but that does
no harm. |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid1,raid10: don't ignore IO flags
If blk-wbt is enabled by default, it's found that raid write performance
is quite bad because all IO are throttled by wbt of underlying disks,
due to flag REQ_IDLE is ignored. And turns out this behaviour exist since
blk-wbt is introduced.
Other than REQ_IDLE, other flags should not be ignored as well, for
example REQ_META can be set for filesystems, clearing it can cause priority
reverse problems; And REQ_NOWAIT should not be cleared as well, because
io will wait instead of failing directly in underlying disks.
Fix those problems by keep IO flags from master bio.
Fises: f51d46d0e7cb ("md: add support for REQ_NOWAIT") |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: avoid journaling sb update on error if journal is destroying
Presently we always BUG_ON if trying to start a transaction on a journal marked
with JBD2_UNMOUNT, since this should never happen. However, while ltp running
stress tests, it was observed that in case of some error handling paths, it is
possible for update_super_work to start a transaction after the journal is
destroyed eg:
(umount)
ext4_kill_sb
kill_block_super
generic_shutdown_super
sync_filesystem /* commits all txns */
evict_inodes
/* might start a new txn */
ext4_put_super
flush_work(&sbi->s_sb_upd_work) /* flush the workqueue */
jbd2_journal_destroy
journal_kill_thread
journal->j_flags |= JBD2_UNMOUNT;
jbd2_journal_commit_transaction
jbd2_journal_get_descriptor_buffer
jbd2_journal_bmap
ext4_journal_bmap
ext4_map_blocks
...
ext4_inode_error
ext4_handle_error
schedule_work(&sbi->s_sb_upd_work)
/* work queue kicks in */
update_super_work
jbd2_journal_start
start_this_handle
BUG_ON(journal->j_flags &
JBD2_UNMOUNT)
Hence, introduce a new mount flag to indicate journal is destroying and only do
a journaled (and deferred) update of sb if this flag is not set. Otherwise, just
fallback to an un-journaled commit.
Further, in the journal destroy path, we have the following sequence:
1. Set mount flag indicating journal is destroying
2. force a commit and wait for it
3. flush pending sb updates
This sequence is important as it ensures that, after this point, there is no sb
update that might be journaled so it is safe to update the sb outside the
journal. (To avoid race discussed in 2d01ddc86606)
Also, we don't need a similar check in ext4_grp_locked_error since it is only
called from mballoc and AFAICT it would be always valid to schedule work here. |
| In the Linux kernel, the following vulnerability has been resolved:
vmxnet3: unregister xdp rxq info in the reset path
vmxnet3 does not unregister xdp rxq info in the
vmxnet3_reset_work() code path as vmxnet3_rq_destroy()
is not invoked in this code path. So, we get below message with a
backtrace.
Missing unregister, handled but fix driver
WARNING: CPU:48 PID: 500 at net/core/xdp.c:182
__xdp_rxq_info_reg+0x93/0xf0
This patch fixes the problem by moving the unregister
code of XDP from vmxnet3_rq_destroy() to vmxnet3_rq_cleanup(). |
| In the Linux kernel, the following vulnerability has been resolved:
bonding: check xdp prog when set bond mode
Following operations can trigger a warning[1]:
ip netns add ns1
ip netns exec ns1 ip link add bond0 type bond mode balance-rr
ip netns exec ns1 ip link set dev bond0 xdp obj af_xdp_kern.o sec xdp
ip netns exec ns1 ip link set bond0 type bond mode broadcast
ip netns del ns1
When delete the namespace, dev_xdp_uninstall() is called to remove xdp
program on bond dev, and bond_xdp_set() will check the bond mode. If bond
mode is changed after attaching xdp program, the warning may occur.
Some bond modes (broadcast, etc.) do not support native xdp. Set bond mode
with xdp program attached is not good. Add check for xdp program when set
bond mode.
[1]
------------[ cut here ]------------
WARNING: CPU: 0 PID: 11 at net/core/dev.c:9912 unregister_netdevice_many_notify+0x8d9/0x930
Modules linked in:
CPU: 0 UID: 0 PID: 11 Comm: kworker/u4:0 Not tainted 6.14.0-rc4 #107
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.15.0-0-g2dd4b9b3f840-prebuilt.qemu.org 04/01/2014
Workqueue: netns cleanup_net
RIP: 0010:unregister_netdevice_many_notify+0x8d9/0x930
Code: 00 00 48 c7 c6 6f e3 a2 82 48 c7 c7 d0 b3 96 82 e8 9c 10 3e ...
RSP: 0018:ffffc90000063d80 EFLAGS: 00000282
RAX: 00000000ffffffa1 RBX: ffff888004959000 RCX: 00000000ffffdfff
RDX: 0000000000000000 RSI: 00000000ffffffea RDI: ffffc90000063b48
RBP: ffffc90000063e28 R08: ffffffff82d39b28 R09: 0000000000009ffb
R10: 0000000000000175 R11: ffffffff82d09b40 R12: ffff8880049598e8
R13: 0000000000000001 R14: dead000000000100 R15: ffffc90000045000
FS: 0000000000000000(0000) GS:ffff888007a00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000000d406b60 CR3: 000000000483e000 CR4: 00000000000006f0
Call Trace:
<TASK>
? __warn+0x83/0x130
? unregister_netdevice_many_notify+0x8d9/0x930
? report_bug+0x18e/0x1a0
? handle_bug+0x54/0x90
? exc_invalid_op+0x18/0x70
? asm_exc_invalid_op+0x1a/0x20
? unregister_netdevice_many_notify+0x8d9/0x930
? bond_net_exit_batch_rtnl+0x5c/0x90
cleanup_net+0x237/0x3d0
process_one_work+0x163/0x390
worker_thread+0x293/0x3b0
? __pfx_worker_thread+0x10/0x10
kthread+0xec/0x1e0
? __pfx_kthread+0x10/0x10
? __pfx_kthread+0x10/0x10
ret_from_fork+0x2f/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30
</TASK>
---[ end trace 0000000000000000 ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
rtnetlink: Allocate vfinfo size for VF GUIDs when supported
Commit 30aad41721e0 ("net/core: Add support for getting VF GUIDs")
added support for getting VF port and node GUIDs in netlink ifinfo
messages, but their size was not taken into consideration in the
function that allocates the netlink message, causing the following
warning when a netlink message is filled with many VF port and node
GUIDs:
# echo 64 > /sys/bus/pci/devices/0000\:08\:00.0/sriov_numvfs
# ip link show dev ib0
RTNETLINK answers: Message too long
Cannot send link get request: Message too long
Kernel warning:
------------[ cut here ]------------
WARNING: CPU: 2 PID: 1930 at net/core/rtnetlink.c:4151 rtnl_getlink+0x586/0x5a0
Modules linked in: xt_conntrack xt_MASQUERADE nfnetlink xt_addrtype iptable_nat nf_nat br_netfilter overlay mlx5_ib macsec mlx5_core tls rpcrdma rdma_ucm ib_uverbs ib_iser libiscsi scsi_transport_iscsi ib_umad rdma_cm iw_cm ib_ipoib fuse ib_cm ib_core
CPU: 2 UID: 0 PID: 1930 Comm: ip Not tainted 6.14.0-rc2+ #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
RIP: 0010:rtnl_getlink+0x586/0x5a0
Code: cb 82 e8 3d af 0a 00 4d 85 ff 0f 84 08 ff ff ff 4c 89 ff 41 be ea ff ff ff e8 66 63 5b ff 49 c7 07 80 4f cb 82 e9 36 fc ff ff <0f> 0b e9 16 fe ff ff e8 de a0 56 00 66 66 2e 0f 1f 84 00 00 00 00
RSP: 0018:ffff888113557348 EFLAGS: 00010246
RAX: 00000000ffffffa6 RBX: ffff88817e87aa34 RCX: dffffc0000000000
RDX: 0000000000000003 RSI: 0000000000000000 RDI: ffff88817e87afb8
RBP: 0000000000000009 R08: ffffffff821f44aa R09: 0000000000000000
R10: ffff8881260f79a8 R11: ffff88817e87af00 R12: ffff88817e87aa00
R13: ffffffff8563d300 R14: 00000000ffffffa6 R15: 00000000ffffffff
FS: 00007f63a5dbf280(0000) GS:ffff88881ee00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f63a5ba4493 CR3: 00000001700fe002 CR4: 0000000000772eb0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
<TASK>
? __warn+0xa5/0x230
? rtnl_getlink+0x586/0x5a0
? report_bug+0x22d/0x240
? handle_bug+0x53/0xa0
? exc_invalid_op+0x14/0x50
? asm_exc_invalid_op+0x16/0x20
? skb_trim+0x6a/0x80
? rtnl_getlink+0x586/0x5a0
? __pfx_rtnl_getlink+0x10/0x10
? rtnetlink_rcv_msg+0x1e5/0x860
? __pfx___mutex_lock+0x10/0x10
? rcu_is_watching+0x34/0x60
? __pfx_lock_acquire+0x10/0x10
? stack_trace_save+0x90/0xd0
? filter_irq_stacks+0x1d/0x70
? kasan_save_stack+0x30/0x40
? kasan_save_stack+0x20/0x40
? kasan_save_track+0x10/0x30
rtnetlink_rcv_msg+0x21c/0x860
? entry_SYSCALL_64_after_hwframe+0x76/0x7e
? __pfx_rtnetlink_rcv_msg+0x10/0x10
? arch_stack_walk+0x9e/0xf0
? rcu_is_watching+0x34/0x60
? lock_acquire+0xd5/0x410
? rcu_is_watching+0x34/0x60
netlink_rcv_skb+0xe0/0x210
? __pfx_rtnetlink_rcv_msg+0x10/0x10
? __pfx_netlink_rcv_skb+0x10/0x10
? rcu_is_watching+0x34/0x60
? __pfx___netlink_lookup+0x10/0x10
? lock_release+0x62/0x200
? netlink_deliver_tap+0xfd/0x290
? rcu_is_watching+0x34/0x60
? lock_release+0x62/0x200
? netlink_deliver_tap+0x95/0x290
netlink_unicast+0x31f/0x480
? __pfx_netlink_unicast+0x10/0x10
? rcu_is_watching+0x34/0x60
? lock_acquire+0xd5/0x410
netlink_sendmsg+0x369/0x660
? lock_release+0x62/0x200
? __pfx_netlink_sendmsg+0x10/0x10
? import_ubuf+0xb9/0xf0
? __import_iovec+0x254/0x2b0
? lock_release+0x62/0x200
? __pfx_netlink_sendmsg+0x10/0x10
____sys_sendmsg+0x559/0x5a0
? __pfx_____sys_sendmsg+0x10/0x10
? __pfx_copy_msghdr_from_user+0x10/0x10
? rcu_is_watching+0x34/0x60
? do_read_fault+0x213/0x4a0
? rcu_is_watching+0x34/0x60
___sys_sendmsg+0xe4/0x150
? __pfx____sys_sendmsg+0x10/0x10
? do_fault+0x2cc/0x6f0
? handle_pte_fault+0x2e3/0x3d0
? __pfx_handle_pte_fault+0x10/0x10
---truncated--- |