| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: pegasus: validate USB endpoints
The pegasus driver should validate that the device it is probing has the
proper number and types of USB endpoints it is expecting before it binds
to it. If a malicious device were to not have the same urbs the driver
will crash later on when it blindly accesses these endpoints. |
| In the Linux kernel, the following vulnerability has been resolved:
IB/mthca: Add missed mthca_unmap_user_db() for mthca_create_srq()
Fix a user triggerable leak on the system call failure path. |
| In the Linux kernel, the following vulnerability has been resolved:
Revert "drm/amd: Check if ASPM is enabled from PCIe subsystem"
This reverts commit 7294863a6f01248d72b61d38478978d638641bee.
This commit was erroneously applied again after commit 0ab5d711ec74
("drm/amd: Refactor `amdgpu_aspm` to be evaluated per device")
removed it, leading to very hard to debug crashes, when used with a system with two
AMD GPUs of which only one supports ASPM.
(cherry picked from commit 97a9689300eb2b393ba5efc17c8e5db835917080) |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring/rw: free potentially allocated iovec on cache put failure
If a read/write request goes through io_req_rw_cleanup() and has an
allocated iovec attached and fails to put to the rw_cache, then it may
end up with an unaccounted iovec pointer. Have io_rw_recycle() return
whether it recycled the request or not, and use that to gauge whether to
free a potential iovec or not. |
| In the Linux kernel, the following vulnerability has been resolved:
net: add proper RCU protection to /proc/net/ptype
Yin Fengwei reported an RCU stall in ptype_seq_show() and provided
a patch.
Real issue is that ptype_seq_next() and ptype_seq_show() violate
RCU rules.
ptype_seq_show() runs under rcu_read_lock(), and reads pt->dev
to get device name without any barrier.
At the same time, concurrent writers can remove a packet_type structure
(which is correctly freed after an RCU grace period) and clear pt->dev
without an RCU grace period.
Define ptype_iter_state to carry a dev pointer along seq_net_private:
struct ptype_iter_state {
struct seq_net_private p;
struct net_device *dev; // added in this patch
};
We need to record the device pointer in ptype_get_idx() and
ptype_seq_next() so that ptype_seq_show() is safe against
concurrent pt->dev changes.
We also need to add full RCU protection in ptype_seq_next().
(Missing READ_ONCE() when reading list.next values)
Many thanks to Dong Chenchen for providing a repro. |
| In the Linux kernel, the following vulnerability has been resolved:
xfs: get rid of the xchk_xfile_*_descr calls
The xchk_xfile_*_descr macros call kasprintf, which can fail to allocate
memory if the formatted string is larger than 16 bytes (or whatever the
nofail guarantees are nowadays). Some of them could easily exceed that,
and Jiaming Zhang found a few places where that can happen with syzbot.
The descriptions are debugging aids and aren't required to be unique, so
let's just pass in static strings and eliminate this path to failure.
Note this patch touches a number of commits, most of which were merged
between 6.6 and 6.14. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: secure_seq: add back ports to TS offset
This reverts 28ee1b746f49 ("secure_seq: downgrade to per-host timestamp offsets")
tcp_tw_recycle went away in 2017.
Zhouyan Deng reported off-path TCP source port leakage via
SYN cookie side-channel that can be fixed in multiple ways.
One of them is to bring back TCP ports in TS offset randomization.
As a bonus, we perform a single siphash() computation
to provide both an ISN and a TS offset. |
| In the Linux kernel, the following vulnerability has been resolved:
audit: add missing syscalls to read class
The "at" variant of getxattr() and listxattr() are missing from the
audit read class. Calling getxattrat() or listxattrat() on a file to
read its extended attributes will bypass audit rules such as:
-w /tmp/test -p rwa -k test_rwa
The current patch adds missing syscalls to the audit read class. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: reject new transactions if the fs is fully read-only
[BUG]
There is a bug report where a heavily fuzzed fs is mounted with all
rescue mount options, which leads to the following warnings during
unmount:
BTRFS: Transaction aborted (error -22)
Modules linked in:
CPU: 0 UID: 0 PID: 9758 Comm: repro.out Not tainted
6.19.0-rc5-00002-gb71e635feefc #7 PREEMPT(full)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014
RIP: 0010:find_free_extent_update_loop fs/btrfs/extent-tree.c:4208 [inline]
RIP: 0010:find_free_extent+0x52f0/0x5d20 fs/btrfs/extent-tree.c:4611
Call Trace:
<TASK>
btrfs_reserve_extent+0x2cd/0x790 fs/btrfs/extent-tree.c:4705
btrfs_alloc_tree_block+0x1e1/0x10e0 fs/btrfs/extent-tree.c:5157
btrfs_force_cow_block+0x578/0x2410 fs/btrfs/ctree.c:517
btrfs_cow_block+0x3c4/0xa80 fs/btrfs/ctree.c:708
btrfs_search_slot+0xcad/0x2b50 fs/btrfs/ctree.c:2130
btrfs_truncate_inode_items+0x45d/0x2350 fs/btrfs/inode-item.c:499
btrfs_evict_inode+0x923/0xe70 fs/btrfs/inode.c:5628
evict+0x5f4/0xae0 fs/inode.c:837
__dentry_kill+0x209/0x660 fs/dcache.c:670
finish_dput+0xc9/0x480 fs/dcache.c:879
shrink_dcache_for_umount+0xa0/0x170 fs/dcache.c:1661
generic_shutdown_super+0x67/0x2c0 fs/super.c:621
kill_anon_super+0x3b/0x70 fs/super.c:1289
btrfs_kill_super+0x41/0x50 fs/btrfs/super.c:2127
deactivate_locked_super+0xbc/0x130 fs/super.c:474
cleanup_mnt+0x425/0x4c0 fs/namespace.c:1318
task_work_run+0x1d4/0x260 kernel/task_work.c:233
exit_task_work include/linux/task_work.h:40 [inline]
do_exit+0x694/0x22f0 kernel/exit.c:971
do_group_exit+0x21c/0x2d0 kernel/exit.c:1112
__do_sys_exit_group kernel/exit.c:1123 [inline]
__se_sys_exit_group kernel/exit.c:1121 [inline]
__x64_sys_exit_group+0x3f/0x40 kernel/exit.c:1121
x64_sys_call+0x2210/0x2210 arch/x86/include/generated/asm/syscalls_64.h:232
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xe8/0xf80 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x44f639
Code: Unable to access opcode bytes at 0x44f60f.
RSP: 002b:00007ffc15c4e088 EFLAGS: 00000246 ORIG_RAX: 00000000000000e7
RAX: ffffffffffffffda RBX: 00000000004c32f0 RCX: 000000000044f639
RDX: 000000000000003c RSI: 00000000000000e7 RDI: 0000000000000001
RBP: 0000000000000001 R08: ffffffffffffffc0 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000004c32f0
R13: 0000000000000001 R14: 0000000000000000 R15: 0000000000000001
</TASK>
Since rescue mount options will mark the full fs read-only, there should
be no new transaction triggered.
But during unmount we will evict all inodes, which can trigger a new
transaction, and triggers warnings on a heavily corrupted fs.
[CAUSE]
Btrfs allows new transaction even on a read-only fs, this is to allow
log replay happen even on read-only mounts, just like what ext4/xfs do.
However with rescue mount options, the fs is fully read-only and cannot
be remounted read-write, thus in that case we should also reject any new
transactions.
[FIX]
If we find the fs has rescue mount options, we should treat the fs as
error, so that no new transaction can be started. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/pm: Disable MMIO access during SMU Mode 1 reset
During Mode 1 reset, the ASIC undergoes a reset cycle and becomes
temporarily inaccessible via PCIe. Any attempt to access MMIO registers
during this window (e.g., from interrupt handlers or other driver threads)
can result in uncompleted PCIe transactions, leading to NMI panics or
system hangs.
To prevent this, set the `no_hw_access` flag to true immediately after
triggering the reset. This signals other driver components to skip
register accesses while the device is offline.
A memory barrier `smp_mb()` is added to ensure the flag update is
globally visible to all cores before the driver enters the sleep/wait
state.
(cherry picked from commit 7edb503fe4b6d67f47d8bb0dfafb8e699bb0f8a4) |
| In the Linux kernel, the following vulnerability has been resolved:
drm: Do not allow userspace to trigger kernel warnings in drm_gem_change_handle_ioctl()
Since GEM bo handles are u32 in the uapi and the internal implementation
uses idr_alloc() which uses int ranges, passing a new handle larger than
INT_MAX trivially triggers a kernel warning:
idr_alloc():
...
if (WARN_ON_ONCE(start < 0))
return -EINVAL;
...
Fix it by rejecting new handles above INT_MAX and at the same time make
the end limit calculation more obvious by moving into int domain. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/damon/sysfs-scheme: cleanup access_pattern subdirs on scheme dir setup failure
When a DAMOS-scheme DAMON sysfs directory setup fails after setup of
access_pattern/ directory, subdirectories of access_pattern/ directory are
not cleaned up. As a result, DAMON sysfs interface is nearly broken until
the system reboots, and the memory for the unremoved directory is leaked.
Cleanup the directories under such failures. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: send: check for inline extents in range_is_hole_in_parent()
Before accessing the disk_bytenr field of a file extent item we need
to check if we are dealing with an inline extent.
This is because for inline extents their data starts at the offset of
the disk_bytenr field. So accessing the disk_bytenr
means we are accessing inline data or in case the inline data is less
than 8 bytes we can actually cause an invalid
memory access if this inline extent item is the first item in the leaf
or access metadata from other items. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf, test_run: Subtract size of xdp_frame from allowed metadata size
The xdp_frame structure takes up part of the XDP frame headroom,
limiting the size of the metadata. However, in bpf_test_run, we don't
take this into account, which makes it possible for userspace to supply
a metadata size that is too large (taking up the entire headroom).
If userspace supplies such a large metadata size in live packet mode,
the xdp_update_frame_from_buff() call in xdp_test_run_init_page() call
will fail, after which packet transmission proceeds with an
uninitialised frame structure, leading to the usual Bad Stuff.
The commit in the Fixes tag fixed a related bug where the second check
in xdp_update_frame_from_buff() could fail, but did not add any
additional constraints on the metadata size. Complete the fix by adding
an additional check on the metadata size. Reorder the checks slightly to
make the logic clearer and add a comment. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Add recursion protection in kernel stack trace recording
A bug was reported about an infinite recursion caused by tracing the rcu
events with the kernel stack trace trigger enabled. The stack trace code
called back into RCU which then called the stack trace again.
Expand the ftrace recursion protection to add a set of bits to protect
events from recursion. Each bit represents the context that the event is
in (normal, softirq, interrupt and NMI).
Have the stack trace code use the interrupt context to protect against
recursion.
Note, the bug showed an issue in both the RCU code as well as the tracing
stacktrace code. This only handles the tracing stack trace side of the
bug. The RCU fix will be handled separately. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath12k: fix dma_free_coherent() pointer
dma_alloc_coherent() allocates a DMA mapped buffer and stores the
addresses in XXX_unaligned fields. Those should be reused when freeing
the buffer rather than the aligned addresses. |
| In the Linux kernel, the following vulnerability has been resolved:
igc: Reduce TSN TX packet buffer from 7KB to 5KB per queue
The previous 7 KB per queue caused TX unit hangs under heavy
timestamping load. Reducing to 5 KB avoids these hangs and matches
the TSN recommendation in I225/I226 SW User Manual Section 7.5.4.
The 8 KB "freed" by this change is currently unused. This reduction
is not expected to impact throughput, as the i226 is PCIe-limited
for small TSN packets rather than TX-buffer-limited. |
| In the Linux kernel, the following vulnerability has been resolved:
pmdomain: imx8m-blk-ctrl: Remove separate rst and clk mask for 8mq vpu
For i.MX8MQ platform, the ADB in the VPUMIX domain has no separate reset
and clock enable bits, but is ungated and reset together with the VPUs.
So we can't reset G1 or G2 separately, it may led to the system hang.
Remove rst_mask and clk_mask of imx8mq_vpu_blk_ctl_domain_data.
Let imx8mq_vpu_power_notifier() do really vpu reset. |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring/io-wq: check IO_WQ_BIT_EXIT inside work run loop
Currently this is checked before running the pending work. Normally this
is quite fine, as work items either end up blocking (which will create a
new worker for other items), or they complete fairly quickly. But syzbot
reports an issue where io-wq takes seemingly forever to exit, and with a
bit of debugging, this turns out to be because it queues a bunch of big
(2GB - 4096b) reads with a /dev/msr* file. Since this file type doesn't
support ->read_iter(), loop_rw_iter() ends up handling them. Each read
returns 16MB of data read, which takes 20 (!!) seconds. With a bunch of
these pending, processing the whole chain can take a long time. Easily
longer than the syzbot uninterruptible sleep timeout of 140 seconds.
This then triggers a complaint off the io-wq exit path:
INFO: task syz.4.135:6326 blocked for more than 143 seconds.
Not tainted syzkaller #0
Blocked by coredump.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:syz.4.135 state:D stack:26824 pid:6326 tgid:6324 ppid:5957 task_flags:0x400548 flags:0x00080000
Call Trace:
<TASK>
context_switch kernel/sched/core.c:5256 [inline]
__schedule+0x1139/0x6150 kernel/sched/core.c:6863
__schedule_loop kernel/sched/core.c:6945 [inline]
schedule+0xe7/0x3a0 kernel/sched/core.c:6960
schedule_timeout+0x257/0x290 kernel/time/sleep_timeout.c:75
do_wait_for_common kernel/sched/completion.c:100 [inline]
__wait_for_common+0x2fc/0x4e0 kernel/sched/completion.c:121
io_wq_exit_workers io_uring/io-wq.c:1328 [inline]
io_wq_put_and_exit+0x271/0x8a0 io_uring/io-wq.c:1356
io_uring_clean_tctx+0x10d/0x190 io_uring/tctx.c:203
io_uring_cancel_generic+0x69c/0x9a0 io_uring/cancel.c:651
io_uring_files_cancel include/linux/io_uring.h:19 [inline]
do_exit+0x2ce/0x2bd0 kernel/exit.c:911
do_group_exit+0xd3/0x2a0 kernel/exit.c:1112
get_signal+0x2671/0x26d0 kernel/signal.c:3034
arch_do_signal_or_restart+0x8f/0x7e0 arch/x86/kernel/signal.c:337
__exit_to_user_mode_loop kernel/entry/common.c:41 [inline]
exit_to_user_mode_loop+0x8c/0x540 kernel/entry/common.c:75
__exit_to_user_mode_prepare include/linux/irq-entry-common.h:226 [inline]
syscall_exit_to_user_mode_prepare include/linux/irq-entry-common.h:256 [inline]
syscall_exit_to_user_mode_work include/linux/entry-common.h:159 [inline]
syscall_exit_to_user_mode include/linux/entry-common.h:194 [inline]
do_syscall_64+0x4ee/0xf80 arch/x86/entry/syscall_64.c:100
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7fa02738f749
RSP: 002b:00007fa0281ae0e8 EFLAGS: 00000246 ORIG_RAX: 00000000000000ca
RAX: fffffffffffffe00 RBX: 00007fa0275e6098 RCX: 00007fa02738f749
RDX: 0000000000000000 RSI: 0000000000000080 RDI: 00007fa0275e6098
RBP: 00007fa0275e6090 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007fa0275e6128 R14: 00007fff14e4fcb0 R15: 00007fff14e4fd98
There's really nothing wrong here, outside of processing these reads
will take a LONG time. However, we can speed up the exit by checking the
IO_WQ_BIT_EXIT inside the io_worker_handle_work() loop, as syzbot will
exit the ring after queueing up all of these reads. Then once the first
item is processed, io-wq will simply cancel the rest. That should avoid
syzbot running into this complaint again. |
| In the Linux kernel, the following vulnerability has been resolved:
ice: fix devlink reload call trace
Commit 4da71a77fc3b ("ice: read internal temperature sensor") introduced
internal temperature sensor reading via HWMON. ice_hwmon_init() was added
to ice_init_feature() and ice_hwmon_exit() was added to ice_remove(). As a
result if devlink reload is used to reinit the device and then the driver
is removed, a call trace can occur.
BUG: unable to handle page fault for address: ffffffffc0fd4b5d
Call Trace:
string+0x48/0xe0
vsnprintf+0x1f9/0x650
sprintf+0x62/0x80
name_show+0x1f/0x30
dev_attr_show+0x19/0x60
The call trace repeats approximately every 10 minutes when system
monitoring tools (e.g., sadc) attempt to read the orphaned hwmon sysfs
attributes that reference freed module memory.
The sequence is:
1. Driver load, ice_hwmon_init() gets called from ice_init_feature()
2. Devlink reload down, flow does not call ice_remove()
3. Devlink reload up, ice_hwmon_init() gets called from
ice_init_feature() resulting in a second instance
4. Driver unload, ice_hwmon_exit() called from ice_remove() leaving the
first hwmon instance orphaned with dangling pointer
Fix this by moving ice_hwmon_exit() from ice_remove() to
ice_deinit_features() to ensure proper cleanup symmetry with
ice_hwmon_init(). |