| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5: Fix MCIA register buffer overflow on 32 dword reads
The MCIA register can return up to 32 dwords (128 bytes) when the device
advertises the mcia_32dwords capability, but struct
mlx5_ifc_mcia_reg_bits only defines dword_0..11, leaving room for just
12 dwords (48 bytes) of data.
mlx5_query_mcia() clamps the read size to mlx5_mcia_max_bytes() and then
memcpy()s that many bytes out of the register, potentially reading past
the end of the 'out' buffer. On kernels built with FORTIFY_SOURCE this
is caught as a buffer overflow while reading the module EEPROM via
ethtool:
detected buffer overflow in memcpy
kernel BUG at lib/string_helpers.c:1048!
RIP: 0010:fortify_panic+0x13/0x20
Call Trace:
mlx5_query_mcia.isra.0+0x200/0x210 [mlx5_core]
mlx5_query_module_eeprom_by_page+0x4a/0xa0 [mlx5_core]
mlx5e_get_module_eeprom_by_page+0xbb/0x120 [mlx5_core]
eeprom_prepare_data+0xf3/0x170
ethnl_default_doit+0xf1/0x3b0
Extend the mcia_reg layout to 32 dwords. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: bound DACL dedup walk to copied ACEs
set_ntacl_dacl() can stop copying ACEs before consuming the full input
DACL when size accounting overflows.
When that happens, num_aces reflects only the ACEs that were actually
copied into the output DACL, but set_posix_acl_entries_dacl() still
receives nt_num_aces and uses it to walk the existing ACE array during
dedup.
That makes the dedup walk scan past the copied ACE array and inspect
buffer tail that does not contain valid ACEs.
Split the two meanings currently carried by the NT ACE count. Pass the
number of copied NT ACEs to bound the dedup walk, and preserve the
original "input DACL had NT ACEs" state separately for the
Everyone/default ACL fallback.
This keeps the dedup walk aligned with the ACEs that are actually
present in the rebuilt DACL. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix OOB read in OnAssocRsp() IE loop
The IE parsing loop in OnAssocRsp() advances by (pIE->length + 2) each
iteration but only guards on i < pkt_len. When a malicious AP sends an
AssocResponse whose last IE has only one byte remaining in the frame
(the element_id byte lands at pkt_len-1), the loop reads pIE->length
from pframe[pkt_len], which is one byte past the allocated receive buffer.
Additionally, even when the header bytes are in bounds, pIE->length
itself can extend the data window beyond pkt_len, silently passing a
truncated IE to the handler functions.
Add two guards at the top of the loop body:
1. Break if fewer than sizeof(*pIE) bytes remain (can't read header).
2. Break if the IE's declared data extends past pkt_len. |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet: fix pre-auth out-of-bounds heap read in Discovery Get Log Page
nvmet_execute_disc_get_log_page() validates only the dword alignment
of the host-supplied Log Page Offset (lpo). The 64-bit offset is then
added to a small kzalloc'd buffer that holds the discovery log page
and the result is passed straight to nvmet_copy_to_sgl(), which
memcpy()s data_len bytes out to the host with no source-side bound
check:
u64 offset = nvmet_get_log_page_offset(req->cmd); /* 64-bit host */
size_t data_len = nvmet_get_log_page_len(req->cmd); /* 32-bit host */
...
if (offset & 0x3) { ... } /* only check */
...
alloc_len = sizeof(*hdr) + entry_size * discovery_log_entries(req);
buffer = kzalloc(alloc_len, GFP_KERNEL);
...
status = nvmet_copy_to_sgl(req, 0, buffer + offset, data_len);
The Discovery controller is unauthenticated -- nvmet_host_allowed()
returns true unconditionally for the discovery subsystem -- so the call
is reachable pre-authentication by any TCP/RDMA/FC peer that can reach
the nvmet target. With a discovery log page of ~1 KiB, an attacker
requesting up to 4 KiB starting at offset == alloc_len reads the next
slab page out and gets its content returned over the fabric (an
empirical run on a default nvmet-tcp loopback target leaked 81
canonical kernel pointers in one Get Log Page response). Pointing the
offset at unmapped kernel memory faults the in-kernel memcpy and
crashes (or panics, on panic_on_oops=1) the target host instead.
The attacker-controlled source-side offset pattern
"nvmet_copy_to_sgl(req, 0, buffer + ATTACKER_OFFSET, ...)" is unique
to nvmet_execute_disc_get_log_page in the entire nvmet codebase: every
other Get Log Page handler in admin-cmd.c either ignores lpo (and
silently starts every response at offset 0) or tracks a local
destination offset with a fixed source pointer.
Validate the host-supplied offset against the log page size, cap the
copy length to what is actually available, and zero-fill any remainder
of the host transfer buffer. The zero-fill matches the existing
short-response pattern in nvmet_execute_get_log_changed_ns()
(admin-cmd.c) and prevents leaking transport SGL contents when the
host asks for more bytes than the log page contains. |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet-auth: validate reply message payload bounds against transfer length
nvmet_auth_reply() accesses the variable-length rval[] array using
attacker-controlled hl (hash length) and dhvlen (DH value length) fields
without verifying they fit within the allocated buffer of tl bytes.
A malicious NVMe-oF initiator can craft a DHCHAP_REPLY message with a
small transfer length but large hl/dhvlen values, causing out-of-bounds
heap reads when the target processes the DH public key (rval + 2*hl) or
performs the host response memcmp.
With DH authentication configured, the OOB pointer is passed directly to
sg_init_one() and read by crypto_kpp_compute_shared_secret(), reaching
up to 526 bytes past the buffer. This is exploitable pre-authentication.
Add bounds validation ensuring sizeof(*data) + 2*hl + dhvlen <= tl before
any access to the variable-length fields.
Discovered by Atuin - Automated Vulnerability Discovery Engine. |
| In the Linux kernel, the following vulnerability has been resolved:
cgroup/rstat: validate cpu before css_rstat_cpu() access
css_rstat_updated() is exposed as a BPF kfunc and accepts a
caller-provided cpu argument. The function uses cpu for per-cpu rstat
lookups without checking whether it refers to a valid possible CPU.
A BPF iter/cgroup program with CAP_BPF and CAP_PERFMON can pass an
invalid cpu value. On an unfixed UBSCAN_BOUNDS test kernel, cpu ==
0x7fffffff triggers:
UBSAN: array-index-out-of-bounds in kernel/cgroup/rstat.c:31:9
index 2147483647 is out of range for type 'long unsigned int [64]'
Call Trace:
css_rstat_updated
bpf_iter_run_prog
cgroup_iter_seq_show
bpf_seq_read
Add cpu validation to the BPF-facing css_rstat_updated() kfunc and
move the common implementation to __css_rstat_updated() for in-kernel
callers. |
| In the Linux kernel, the following vulnerability has been resolved:
security/keys: fix missed RCU read section on lookup
Nicholas Carlini reports that the keyring code calls assoc_array_find()
in find_key_to_update() without holding the RCU read lock, while the
assoc_array_gc() code really is designed around removing the node from
the tree and then freeing it after an RCU grace-period.
The regular key handling doesn't see this because holding the keyring
semaphore hides any lifetime issues, but the persistent key handling
uses a different model.
Instead of extending the keyring locking, just do the simple RCU locking
that the assoc_array was designed for. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/vcn: set no_user_fence for VCN v2.5 enc/dec rings
VCN encoder and decoder rings do not support 64-bit user fence writes,
reject CS submissions with user fences.
(cherry picked from commit efc9dd5590894109bce9a0bfe1fa5592dd6b20b1) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/vcn: set no_user_fence for VCN v4.0 enc ring
VCN encoder and decoder rings do not support 64-bit user fence writes,
reject CS submissions with user fences.
(cherry picked from commit fd852c048b46f9825e904a4f3f4538fe9d8827d9) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/jpeg: set no_user_fence for JPEG v3.0 ring
JPEG rings do not support 64-bit user fence writes, reject CS
submissions with user fences.
(cherry picked from commit 4d7d774f100efb5089c86a1fb8c5bf47c63fc9ef) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Fix out-of-bounds read in dp_get_eq_aux_rd_interval()
[Why & How]
The aux_rd_interval array in struct dc_lttpr_caps is declared with
MAX_REPEATER_CNT - 1 (7) elements, indexed 0..6. However, the offset
parameter passed to dp_get_eq_aux_rd_interval() can be as large as
MAX_REPEATER_CNT (8) when a sink reports 8 LTTPR repeaters via DPCD.
This leads to an out-of-bounds read of aux_rd_interval[7] when offset
is 8.
Fix this by growing aux_rd_interval to MAX_REPEATER_CNT elements to
accommodate the full range of valid repeater counts defined by the DP
spec.
(cherry picked from commit a55a458a8df37a65ffda5cf721d554a8f74f6b04) |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nft_ct: bail out on template ct in get eval
I noticed this issue while looking at a historic syzbot report [1].
A rule like the one below is enough to trigger the bug:
table ip t {
chain pre {
type filter hook prerouting priority raw;
ct zone set 1
ct original saddr 1.2.3.4 accept
}
}
The first expression attaches a per-cpu template ct via
nft_ct_set_zone_eval() (nf_ct_tmpl_alloc -> kzalloc, tuple is all
zero, nf_ct_l3num(ct) == 0). The next expression then calls
nft_ct_get_eval() on the same skb, treats the template as a real ct
and hits the 16-byte memcpy path. With dreg at NFT_REG32_15 this
overflows past struct nft_regs on the kernel stack; with smaller
dreg values it silently clobbers adjacent registers.
Reject template ct at the eval entry and in nft_ct_get_fast_eval(),
mirroring the check nft_ct_set_eval() already has. Additionally,
bound the address copy in NFT_CT_SRC / NFT_CT_DST by priv->len
instead of by nf_ct_l3num(ct): nf_ct_get_tuple() zeroes the tuple
before pkt_to_tuple() fills in only the protocol-relevant leading
bytes, so the trailing bytes of tuple->{src,dst}.u3.all are
well-defined zero. priv->len is validated at rule load, so the
copy size is now bounded by the destination register rather than
by an untrusted field on the conntrack.
[1]: https://syzkaller.appspot.com/bug?id=389cf09cb72926114fce90dc85a2c3231dcb647c |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5: Fix slab-out-of-bounds in mlx5_query_nic_vport_mac_list
mlx5_query_nic_vport_mac_list() sizes its firmware command buffer using
the PF's log_max_current_uc/mc_list capabilities. When querying a VF
vport with a larger configured max (via devlink), the firmware response
can overflow this buffer:
BUG: KASAN: slab-out-of-bounds in mlx5_query_nic_vport_mac_list+0x453/0x4c0 [mlx5_core]
Read of size 4 at addr ff1100013ffc8a12 by task kworker/u96:2/385
CPU: 12 UID: 0 PID: 385 Comm: kworker/u96:2 Not tainted 7.0.0-rc6+ #1 PREEMPT
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009)
Workqueue: mlx5_esw_wq esw_vport_change_handler [mlx5_core]
Call Trace:
<TASK>
dump_stack_lvl+0x69/0xa0
print_report+0x176/0x4e4
kasan_report+0xc8/0x100
mlx5_query_nic_vport_mac_list+0x453/0x4c0 [mlx5_core]
esw_update_vport_addr_list+0x2e3/0xda0 [mlx5_core]
esw_vport_change_handle_locked+0xa1f/0x1060 [mlx5_core]
esw_vport_change_handler+0x6a/0x90 [mlx5_core]
process_one_work+0x87f/0x15e0
worker_thread+0x62b/0x1020
kthread+0x375/0x490
ret_from_fork+0x4dc/0x810
ret_from_fork_asm+0x11/0x20
</TASK>
Fix by querying the vport's own HCA caps to size the buffer correctly.
Refactor the function to allocate and return the MAC list internally,
removing the caller's dependency on knowing the correct max. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: validate embedded INIT chunk and address list lengths in cookie
sctp_unpack_cookie() only checked that the embedded INIT chunk length
did not exceed the remaining cookie payload, but did not ensure that the
INIT chunk is large enough to contain a complete INIT header.
A malformed COOKIE_ECHO can therefore carry a truncated INIT chunk whose
length field is smaller than sizeof(struct sctp_init_chunk). Later,
sctp_process_init() accesses INIT parameters unconditionally, which may
lead to out-of-bounds reads.
In addition, raw_addr_list_len is not fully validated against the
remaining cookie payload. When cookie authentication is disabled, an
attacker can supply an oversized raw_addr_list_len and cause
sctp_raw_to_bind_addrs() to read beyond the end of the cookie. The
address parser also lacks sufficient bounds checks for parameter headers
and lengths, allowing malformed address parameters to trigger
out-of-bounds reads.
Fix this by:
- requiring the embedded INIT chunk length to be at least sizeof(struct
sctp_init_chunk);
- validating that the INIT chunk and raw address list together fit
within the cookie payload;
- verifying sufficient data exists for each address parameter header and
payload before parsing it.
Note that sctp_verify_init() must be called after sctp_unpack_cookie()
and before sctp_process_init() when cookie authentication is disabled.
This will be addressed in a separate patch. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix OOB in pcpu_init_value
An out-of-bounds read occurs when copying element from a
BPF_MAP_TYPE_CGROUP_STORAGE map to another pcpu map with the
same value_size that is not rounded up to 8 bytes.
The issue happens when:
1. A CGROUP_STORAGE map is created with value_size not aligned to
8 bytes (e.g., 4 bytes)
2. A pcpu map is created with the same value_size (e.g., 4 bytes)
3. Update element in 2 with data in 1
pcpu_init_value assumes that all sources are rounded up to 8 bytes,
and invokes copy_map_value_long to make a data copy, However, the
assumption doesn't stand since there are some cases where the source
may not be rounded up to 8 bytes, e.g., CGROUP_STORAGE, skb->data.
the verifier verifies exactly the size that the source claims, not
the size rounded up to 8 bytes by kernel, an OOB happens when the
source has only 4 bytes while the copy size(4) is rounded up to 8. |
| In the Linux kernel, the following vulnerability has been resolved:
libceph: Fix potential out-of-bounds access in __ceph_x_decrypt()
In __ceph_x_decrypt(), a part of the buffer p is interpreted as a
ceph_x_encrypt_header, and the magic field of this struct is accessed.
This happens without any guarantee that the buffer is large enough to
hold this struct. The function parameter ciphertext_len represents the
length of the ciphertext to decrypt and is guaranteed to be at most the
remaining size of the allocated buffer p. However, this value is not
necessarily greater than sizeof(ceph_x_encrypt_header). E.g., a message
frame of type FRAME_TAG_AUTH_REPLY_MORE, that is just as long to hold
the ciphertext at its end with a ciphertext_len of 8 or less, can
trigger an out-of-bounds memory access when accessing hdr->magic.
This patch fixes the issue by adding a check to ensure that the
decrypted plaintext in the buffer is large enough to represent at least
the ceph_x_encrypt_header. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/vcn4: Prevent OOB reads when parsing IB
Rewrite the IB parsing to use amdgpu_ib_get_value() which handles the
bounds checks. |
| In the Linux kernel, the following vulnerability has been resolved:
rcu: Fix rcu_read_unlock() deadloop due to softirq
Commit 5f5fa7ea89dc ("rcu: Don't use negative nesting depth in
__rcu_read_unlock()") removes the recursion-protection code from
__rcu_read_unlock(). Therefore, we could invoke the deadloop in
raise_softirq_irqoff() with ftrace enabled as follows:
WARNING: CPU: 0 PID: 0 at kernel/trace/trace.c:3021 __ftrace_trace_stack.constprop.0+0x172/0x180
Modules linked in: my_irq_work(O)
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Tainted: G O 6.18.0-rc7-dirty #23 PREEMPT(full)
Tainted: [O]=OOT_MODULE
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014
RIP: 0010:__ftrace_trace_stack.constprop.0+0x172/0x180
RSP: 0018:ffffc900000034a8 EFLAGS: 00010002
RAX: 0000000000000000 RBX: 0000000000000004 RCX: 0000000000000000
RDX: 0000000000000003 RSI: ffffffff826d7b87 RDI: ffffffff826e9329
RBP: 0000000000090009 R08: 0000000000000005 R09: ffffffff82afbc4c
R10: 0000000000000008 R11: 0000000000011d7a R12: 0000000000000000
R13: ffff888003874100 R14: 0000000000000003 R15: ffff8880038c1054
FS: 0000000000000000(0000) GS:ffff8880fa8ea000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055b31fa7f540 CR3: 00000000078f4005 CR4: 0000000000770ef0
PKRU: 55555554
Call Trace:
<IRQ>
trace_buffer_unlock_commit_regs+0x6d/0x220
trace_event_buffer_commit+0x5c/0x260
trace_event_raw_event_softirq+0x47/0x80
raise_softirq_irqoff+0x6e/0xa0
rcu_read_unlock_special+0xb1/0x160
unwind_next_frame+0x203/0x9b0
__unwind_start+0x15d/0x1c0
arch_stack_walk+0x62/0xf0
stack_trace_save+0x48/0x70
__ftrace_trace_stack.constprop.0+0x144/0x180
trace_buffer_unlock_commit_regs+0x6d/0x220
trace_event_buffer_commit+0x5c/0x260
trace_event_raw_event_softirq+0x47/0x80
raise_softirq_irqoff+0x6e/0xa0
rcu_read_unlock_special+0xb1/0x160
unwind_next_frame+0x203/0x9b0
__unwind_start+0x15d/0x1c0
arch_stack_walk+0x62/0xf0
stack_trace_save+0x48/0x70
__ftrace_trace_stack.constprop.0+0x144/0x180
trace_buffer_unlock_commit_regs+0x6d/0x220
trace_event_buffer_commit+0x5c/0x260
trace_event_raw_event_softirq+0x47/0x80
raise_softirq_irqoff+0x6e/0xa0
rcu_read_unlock_special+0xb1/0x160
unwind_next_frame+0x203/0x9b0
__unwind_start+0x15d/0x1c0
arch_stack_walk+0x62/0xf0
stack_trace_save+0x48/0x70
__ftrace_trace_stack.constprop.0+0x144/0x180
trace_buffer_unlock_commit_regs+0x6d/0x220
trace_event_buffer_commit+0x5c/0x260
trace_event_raw_event_softirq+0x47/0x80
raise_softirq_irqoff+0x6e/0xa0
rcu_read_unlock_special+0xb1/0x160
__is_insn_slot_addr+0x54/0x70
kernel_text_address+0x48/0xc0
__kernel_text_address+0xd/0x40
unwind_get_return_address+0x1e/0x40
arch_stack_walk+0x9c/0xf0
stack_trace_save+0x48/0x70
__ftrace_trace_stack.constprop.0+0x144/0x180
trace_buffer_unlock_commit_regs+0x6d/0x220
trace_event_buffer_commit+0x5c/0x260
trace_event_raw_event_softirq+0x47/0x80
__raise_softirq_irqoff+0x61/0x80
__flush_smp_call_function_queue+0x115/0x420
__sysvec_call_function_single+0x17/0xb0
sysvec_call_function_single+0x8c/0xc0
</IRQ>
Commit b41642c87716 ("rcu: Fix rcu_read_unlock() deadloop due to IRQ work")
fixed the infinite loop in rcu_read_unlock_special() for IRQ work by
setting a flag before calling irq_work_queue_on(). We fix this issue by
setting the same flag before calling raise_softirq_irqoff() and rename the
flag to defer_qs_pending for more common. |
| In the Linux kernel, the following vulnerability has been resolved:
erofs: fix inline data read failure for ztailpacking pclusters
Compressed folios for ztailpacking pclusters must be valid before adding
these pclusters to I/O chains. Otherwise, z_erofs_decompress_pcluster()
may assume they are already valid and then trigger a NULL pointer
dereference.
It is somewhat hard to reproduce because the inline data is in the same
block as the tail of the compressed indexes, which are usually read just
before. However, it may still happen if a fatal signal arrives while
read_mapping_folio() is running, as shown below:
erofs: (device dm-1): z_erofs_pcluster_begin: failed to get inline data -4
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000008
...
pc : z_erofs_decompress_queue+0x4c8/0xa14
lr : z_erofs_decompress_queue+0x160/0xa14
sp : ffffffc08b3eb3a0
x29: ffffffc08b3eb570 x28: ffffffc08b3eb418 x27: 0000000000001000
x26: ffffff8086ebdbb8 x25: ffffff8086ebdbb8 x24: 0000000000000001
x23: 0000000000000008 x22: 00000000fffffffb x21: dead000000000700
x20: 00000000000015e7 x19: ffffff808babb400 x18: ffffffc089edc098
x17: 00000000c006287d x16: 00000000c006287d x15: 0000000000000004
x14: ffffff80ba8f8000 x13: 0000000000000004 x12: 00000006589a77c9
x11: 0000000000000015 x10: 0000000000000000 x9 : 0000000000000000
x8 : 0000000000000000 x7 : 0000000000000000 x6 : 000000000000003f
x5 : 0000000000000040 x4 : ffffffffffffffe0 x3 : 0000000000000020
x2 : 0000000000000008 x1 : 0000000000000000 x0 : 0000000000000000
Call trace:
z_erofs_decompress_queue+0x4c8/0xa14
z_erofs_runqueue+0x908/0x97c
z_erofs_read_folio+0x128/0x228
filemap_read_folio+0x68/0x128
filemap_get_pages+0x44c/0x8b4
filemap_read+0x12c/0x5b8
generic_file_read_iter+0x4c/0x15c
do_iter_readv_writev+0x188/0x1e0
vfs_iter_read+0xac/0x1a4
backing_file_read_iter+0x170/0x34c
ovl_read_iter+0xf0/0x140
vfs_read+0x28c/0x344
ksys_read+0x80/0xf0
__arm64_sys_read+0x24/0x34
invoke_syscall+0x60/0x114
el0_svc_common+0x88/0xe4
do_el0_svc+0x24/0x30
el0_svc+0x40/0xa8
el0t_64_sync_handler+0x70/0xbc
el0t_64_sync+0x1bc/0x1c0
Fix this by reading the inline data before allocating and adding
the pclusters to the I/O chains. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix EEXIST abort due to non-consecutive gaps in chunk allocation
I have been observing a number of systems aborting at
insert_dev_extents() in btrfs_create_pending_block_groups(). The
following is a sample stack trace of such an abort coming from forced
chunk allocation (typically behind CONFIG_BTRFS_EXPERIMENTAL) but this
can theoretically happen to any DUP chunk allocation.
[81.801] ------------[ cut here ]------------
[81.801] BTRFS: Transaction aborted (error -17)
[81.801] WARNING: fs/btrfs/block-group.c:2876 at btrfs_create_pending_block_groups+0x721/0x770 [btrfs], CPU#1: bash/319
[81.802] Modules linked in: virtio_net btrfs xor zstd_compress raid6_pq null_blk
[81.803] CPU: 1 UID: 0 PID: 319 Comm: bash Kdump: loaded Not tainted 6.19.0-rc6+ #319 NONE
[81.803] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Arch Linux 1.17.0-2-2 04/01/2014
[81.804] RIP: 0010:btrfs_create_pending_block_groups+0x723/0x770 [btrfs]
[81.806] RSP: 0018:ffffa36241a6bce8 EFLAGS: 00010282
[81.806] RAX: 000000000000000d RBX: ffff8e699921e400 RCX: 0000000000000000
[81.807] RDX: 0000000002040001 RSI: 00000000ffffffef RDI: ffffffffc0608bf0
[81.807] RBP: 00000000ffffffef R08: ffff8e69830f6000 R09: 0000000000000007
[81.808] R10: ffff8e699921e5e8 R11: 0000000000000000 R12: ffff8e6999228000
[81.808] R13: ffff8e6984d82000 R14: ffff8e69966a69c0 R15: ffff8e69aa47b000
[81.809] FS: 00007fec6bdd9740(0000) GS:ffff8e6b1b379000(0000) knlGS:0000000000000000
[81.809] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[81.810] CR2: 00005604833670f0 CR3: 0000000116679000 CR4: 00000000000006f0
[81.810] Call Trace:
[81.810] <TASK>
[81.810] __btrfs_end_transaction+0x3e/0x2b0 [btrfs]
[81.811] btrfs_force_chunk_alloc_store+0xcd/0x140 [btrfs]
[81.811] kernfs_fop_write_iter+0x15f/0x240
[81.812] vfs_write+0x264/0x500
[81.812] ksys_write+0x6c/0xe0
[81.812] do_syscall_64+0x66/0x770
[81.812] entry_SYSCALL_64_after_hwframe+0x76/0x7e
[81.813] RIP: 0033:0x7fec6be66197
[81.814] RSP: 002b:00007fffb159dd30 EFLAGS: 00000202 ORIG_RAX: 0000000000000001
[81.815] RAX: ffffffffffffffda RBX: 00007fec6bdd9740 RCX: 00007fec6be66197
[81.815] RDX: 0000000000000002 RSI: 0000560483374f80 RDI: 0000000000000001
[81.816] RBP: 0000560483374f80 R08: 0000000000000000 R09: 0000000000000000
[81.816] R10: 0000000000000000 R11: 0000000000000202 R12: 0000000000000002
[81.817] R13: 00007fec6bfb85c0 R14: 00007fec6bfb5ee0 R15: 00005604833729c0
[81.817] </TASK>
[81.817] irq event stamp: 20039
[81.818] hardirqs last enabled at (20047): [<ffffffff99a68302>] __up_console_sem+0x52/0x60
[81.818] hardirqs last disabled at (20056): [<ffffffff99a682e7>] __up_console_sem+0x37/0x60
[81.819] softirqs last enabled at (19470): [<ffffffff999d2b46>] __irq_exit_rcu+0x96/0xc0
[81.819] softirqs last disabled at (19463): [<ffffffff999d2b46>] __irq_exit_rcu+0x96/0xc0
[81.820] ---[ end trace 0000000000000000 ]---
[81.820] BTRFS: error (device dm-7 state A) in btrfs_create_pending_block_groups:2876: errno=-17 Object already exists
Inspecting these aborts with drgn, I observed a pattern of overlapping
chunk_maps. Note how stripe 1 of the first chunk overlaps in physical
address with stripe 0 of the second chunk.
Physical Start Physical End Length Logical Type Stripe
----------------------------------------------------------------------------------------------------
0x0000000102500000 0x0000000142500000 1.0G 0x0000000641d00000 META|DUP 0/2
0x0000000142500000 0x0000000182500000 1.0G 0x0000000641d00000 META|DUP 1/2
0x0000000142500000 0x0000000182500000 1.0G 0x0000000601d00000 META|DUP 0/2
0x0000000182500000 0x00000001c2500000 1.0G 0x0000000601d00000 META|DUP 1/2
Now how could this possibly happen? All chunk allocation is
---truncated--- |